arcade:joystick_mechs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arcade:joystick_mechs [2023/11/25 13:49] – NFG | arcade:joystick_mechs [2024/01/06 08:51] – [Sanwa] NFG | ||
---|---|---|---|
Line 2: | Line 2: | ||
Just a fun-filled list of joystick mounts for easy fact finding. | Just a fun-filled list of joystick mounts for easy fact finding. | ||
- | ==== Seimitsu ==== | + | ===== Seimitsu |
Seimitsu sticks to two mounting patterns, for the most part. Either a 50mm square, or 40mm. | Seimitsu sticks to two mounting patterns, for the most part. Either a 50mm square, or 40mm. | ||
Line 11: | Line 11: | ||
Their entire catalogue of available plates (in 2023) is available on the [[arcade: | Their entire catalogue of available plates (in 2023) is available on the [[arcade: | ||
- | === Seimitsu 40mm Mechs === | + | ==== Seimitsu 40mm Mechs ==== |
Most of Seimitsu' | Most of Seimitsu' | ||
+ | |||
+ | {{ : | ||
* SELS-70X | * SELS-70X | ||
Line 21: | Line 23: | ||
* LS-55 | * LS-55 | ||
- | === Seimitsu 50mm Mechs === | + | ==== Seimitsu 50mm Mechs ==== |
* LS-32 | * LS-32 | ||
Line 27: | Line 29: | ||
* NOBI | * NOBI | ||
- | ==== SNK ==== | + | ===== SNK / Sigma / ASCII / Seimitsu ===== |
- | SNK's home consoles used Seimitsu mechs (or clones of them) with a 40mm pattern. | + | SNK's home consoles used Seimitsu mechs (or clones of them) with a 40mm pattern. Shown below is a mech from a NeoGeo AES joystick (the original and CD sticks used the same mechs). |
- | {{: | + | These same mechs (or clones of them) were also used in sticks from Sigma (The Σ-2200 definitely used a Seimitsu mech) and (IIRC) ASCII. |
- | ==== Sanwa ==== | + | {{:arcade:snk-stick.jpg?200|SNK's NeoGeo AES Stick Mech}}{{: |
- | Sanwa uses two mount patterns: either a simple 65mm two-screw attachment, or a square pattern that's much smaller than Seimitsu' | + | |
- | ==== Hori ==== | + | ===== Sanwa ===== |
- | Hori's made many mechs throughout their history. | + | Sanwa' |
+ | |||
+ | {{ : | ||
+ | |||
+ | The two 65mm holes in both the JLX and JLF are not threaded, and typically use a nut & bolt attachment. | ||
+ | |||
+ | The JLF 4-hole mounts are plastic and use self-tapping counter-sink screws to fix the mech to the plate. The JLX sticks however use threaded metal inserts, and so must use different screws than the JLF mechs. | ||
+ | |||
+ | Sanwa sticks are mounted deeper into the panel compared to Seimitsu sticks. | ||
+ | |||
+ | Sanwa sticks use a raised central circle around the pivot, to allow for the pivot to rise vertically above the nominal surface of the stick. | ||
+ | ===== Hori ===== | ||
+ | Hori's made many mechs throughout their history. | ||
{{: | {{: | ||
- | The Hayabusa shown above includes the mounting plate. | + | The Hayabusa shown above includes the mounting plate. |
+ | |||
+ | [[Hori Hayabusa|Hori Hayabusa Info Page]] | ||
+ | |||
+ | ===== ASCII ===== | ||
+ | ASCII made many joysticks, and distributed Sega's Dreamcast arcade stick in North America (as Agetech). | ||
+ | |||
+ | === CX4J === | ||
+ | ASCII were first to market with an optical mechanism, it is branded ASCII (and OMRON) with a part number C4XJ. It was used in several Playstation and Dreamcast sticks, like the [[controls: | ||
+ | |||
+ | It was possibly developed with Sanwa, who later released a nearly identical unit called the **JLHS-8 FLASH 1**. It uses two groups of soldered-on wires, 4-wires for the directional outputs, and two wires for Vcc and Ground, to power the LEDs. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | This mech is compatible with Sanwa JLF mounts and accessories. |
arcade/joystick_mechs.txt · Last modified: 2024/06/21 00:10 by NFG