User Tools

Site Tools


av:nintendodigitalav

Differences

This shows you the differences between two versions of the page.


Previous revision
av:nintendodigitalav [2010/04/19 15:57] sophia
Line 1: Line 1:
-===== Nintendo GameCube Digital AV Connector ===== 
-The DigitalAV connector carries digital sound and digital component video.  Neither signal is useful by itself(I've read it on some [[http://cvresumewritingservices.org/professional-resume.php|professional resume services]] site); the Nintendo component cable converts the digital to analogue component, and a chip is required to convert the digital audio to a usable format (TOSlink, etc).  Special thanks to **Oscar** for this information. 
  
-There are other pages detailing the [[nintendoGCRGB|GameCube RGB + VGA]] and [[nintendoGCDA|Digital Audio]] mods on this wiki. 
- 
-<box warning round|Caveats> 
-  * Most GameCubes have the digital connector, however to reduce costs Nintendo removed the port from newer systems.  In times past Nintendo would exchange your console for one with the digital connector port on request. As of August 2006, they no longer offer this service .They instead offer assistance finding a used console with the appropriate port. 
-  * The GameCube is capable of creating a progressive signal, however the software must support it.  No PAL software utilizes the progressive capability of the hardware (so no VGA either). 
-</box> 
- 
-==== The Connector ==== 
-{{:av:gamecubedigital1.png|}} 
-\\ \\ 
-^ GameCube Digital Connector ^^^^ 
-^ Pin ^ Signal ^ Pin ^ Signal ^ 
-^  1 | DetectCable (pull high 1.8V)  |  2 | 54MHz Clock  | 
-^  3 | ClkSelect(CP10)  |  4 | GND  | 
-^  5 | +12V  |  6 | 27MHz Clock  | 
-^  7 | VDATA0 (CP09)  |  8 | GND  | 
-^  9 | VDATA1 (CP08)  |  10 | VDATA2 (CP07)  | 
-^  11 | GND  |  12 | VDATA3 (CP06)  | 
-^  13 | VDATA4 (CP04)  |  14 | GND  | 
-^  15 | VDATA5 (CP03)  |  16 | VDATA6 (CP02)  | 
-^  17 | +3.3V  |  18 | VDATA7 (CP01)  | 
-^  19 | LRCK (Audio)  |  20 | GND  | 
-^  21 | Data (Audio)  |  22 | BCLK (Audio)  | 
-| Note: (CPxx) = Chip Pin # |||| 
- 
-Video is sent as 4:2:2 YCrCb component. 
-<Y><Cr><Y><Cb><Y><Cr><Y><Cb>\\ 
-Y is set to 0 during blanking intervals, and Cr/Cb packets are used to transmit sync and flag information. 
-\\ \\ 
- 
-==== The Flags ==== 
-\\ 
-^Flags^^^^ 
-^Bit^Flag^Description^Options^ 
-^0^I^Interlaced Flag^0 = Interlaced, 1 = Non-Interlaced^ 
-^1^M^Screen Mode Flag^0 = NTSC, 1 = PAL^ 
-^2^K^Color Burst Blanking Flag^0 = Color Burst Should be Blanked Out^ 
-^3^B^Color Burst Flag^0 = Indicates location of Color Burst^ 
-^4^H^Horizontal Sync^0 = Horizontal Sync Active^ 
-^5^V^Vertical Sync^0 = Verical Sync Active^ 
-^6^F^Field^0 = Odd Field, 1 = Even Field^ 
-^7^C^Composite Sync^0 = Composite Sync Active^ 
-|Note: Odd fields start Y:Cb Even fields start Y:Cr|||| 
- 
- 
-==== The CMPV-DOL Chip ==== 
-This is the chip used in the official Nintendo component cables.  It's manufactured by Macronix, but is an ASIC (application-specific IC) made exclusively for Nintendo and neither company, as of February 2008, will divulge its secrets.  The image below shows a cable with the RGB mod applied, hence the RGB select wire on pin 12, and the H/V Sync on pins 21 + 22. 
- 
-{{av:gamecubedigital3.png }}  
- 
-^ Macronix CMPV-DOL Pinout ^^^^ 
-^ Pin ^ Signal ^ Pin ^ Signal ^ 
-^  1 | VDATA7  |  2 | VDATA6  | 
-^  3 | VDATA5  |  4 | VDATA4  | 
-^  5 | 3.3V  |  6 | VDATA3  | 
-^  7 | VDATA2  |  8 | VDATA1  | 
-^  9 | VDATA0  |  10 | ClkSelect | 
-^  11 | 54MHz Clock  |  12 | GND  | 
-^  13 | *  |  14 | *  | 
-^  15 | RED/Pr  |  16 | GND  | 
-^  17 | BLUE/Pb  |  18 | 3.3V  | 
-^  19 | GREEN/ |  20 | SENS  | 
-^  21 | H-Sync  |  22 | V-Sync  | 
-^  23 | GND  |  24 | GND  | 
-| *1.2V Compensation or Filter?? |||| 
av/nintendodigitalav.txt · Last modified: 2023/05/26 08:44 by Link83