User Tools

Site Tools


controls:snes_con_region_fix

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Last revisionBoth sides next revision
controls:snes_con_region_fix [2008/07/23 17:46] 122.49.159.159controls:snes_con_region_fix [2008/07/23 17:58] 122.49.159.159
Line 25: Line 25:
 For the other revision, you will need the same two resistors, but because the PCB lacks places for the 'only-P' resistors, you will have to solder to other points on the pcb. The following picture shows where the resistors should be soldered on these PCB revisions, the 1.2k resistor should be soldered between the two red points, and the 3k resistor soldered between the two blue points. For the other revision, you will need the same two resistors, but because the PCB lacks places for the 'only-P' resistors, you will have to solder to other points on the pcb. The following picture shows where the resistors should be soldered on these PCB revisions, the 1.2k resistor should be soldered between the two red points, and the 3k resistor soldered between the two blue points.
  
-[[http://phreak97.experienced.tk/phreak97/GameSX/resistorsbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/resistors.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/resistorsbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/resistors.jpg|Click to Enlarge}}]]
  
 If you find it too difficult to solder the resistors directly to these points, you may run wires from them and put the resistors anywhere you like inside the controller, so long as they are fixed down with something like electrical tape or hot glue, and will not move about. If you find it too difficult to solder the resistors directly to these points, you may run wires from them and put the resistors anywhere you like inside the controller, so long as they are fixed down with something like electrical tape or hot glue, and will not move about.
Line 42: Line 42:
  
 === Pad Externals === === Pad Externals ===
-[[http://phreak97.experienced.tk/phreak97/GameSX/snesconsbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/snescons.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/snesconsbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/snescons.jpg|Click to Enlarge}}]]
   * Click for larger image   * Click for larger image
  
 === Pad Internals === === Pad Internals ===
-[[http://phreak97.experienced.tk/phreak97/GameSX/internalsbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/internals.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/internalsbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/internals.jpg|Click to Enlarge}}]]
   * Click for larger image   * Click for larger image
  
 == US Pad == == US Pad ==
  
-[[http://phreak97.experienced.tk/phreak97/GameSX/usconbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/uscon.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/usconbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/uscon.jpg|Click to Enlarge}}]]
  
 == Japanese Pad == == Japanese Pad ==
  
-[[http://phreak97.experienced.tk/phreak97/GameSX/sfcconbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/sfccon.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/sfcconbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/sfccon.jpg|Click to Enlarge}}]]
   * Note the unused solder pads for resistors R1 and R2 (Also highlighted in white, and labled 'only-P', meaning 'only PAL').   * Note the unused solder pads for resistors R1 and R2 (Also highlighted in white, and labled 'only-P', meaning 'only PAL').
  
 == PAL Pad == == PAL Pad ==
  
-[[http://phreak97.experienced.tk/phreak97/GameSX/palconbig.jpg|{{http://phreak97.experienced.tk/phreak97/GameSX/palcon.jpg|Click to Enlarge}}]]+[[http://i189.photobucket.com/albums/z234/phreak97/snescons/palconbig.jpg|{{http://i189.photobucket.com/albums/z234/phreak97/snescons/palcon.jpg|Click to Enlarge}}]]
   * Note the resistors at R1 and R2 (only-P positions).    * Note the resistors at R1 and R2 (only-P positions). 
     * R1 is a 1.2k resistor (labled '122'     * R1 is a 1.2k resistor (labled '122'
controls/snes_con_region_fix.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1