x68000:xsimm10_-_memory_expansion_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
x68000:xsimm10_-_memory_expansion_board [2011/12/03 05:44] – eidis | x68000:xsimm10_-_memory_expansion_board [2019/08/27 20:45] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 5: | Line 5: | ||
{{: | {{: | ||
- | XSIMM10 (Ten X-Sim) | + | XSIMM10 (Ten X-Sim) |
- | This product, SIMM modules | + | |
|{{: | |{{: | ||
| XSIMM10 | | XSIMM10 | ||
- | **Selection and implementation of the SIMM module** | + | **Compatible |
- | This XSIMM (Single In-line Memory Module) | + | The XSIMM10 board can be used with the following |
- | For compatible machines • PC / AT: 9 bit (with parity) for the 30-pin Macintosh: 30-pin 8-bit, however, from bandwidth limitations I / O expansion slots, the following restrictions to the size of the SIMM module vertical board The. | + | |
- | • For mounting slot 1: Mounted on the following two slots 15.3mm: below this size exceeds 20.4mm, is that if the adjacent slot unusable. | + | |
- | In addition, when used with the following models, you must have a total of 2MB internal memory to add more RAM and 1MB of internal memory boards in advance. | + | |
- | {{:x68000:xsimm10_3.jpg? | + | *PC/AT: 9-bit (with parity) 30-pin |
+ | *Macintosh: 8-bit, 30-pin | ||
- | XSIMM10 one pair of two SIMM modules have the same access time and memory capacity per pair as a pair or two pairs can be expandable to up to 10MB. | + | However, |
- | SIMM memory modules that can be used per sheet, the sheet is 4MB / images or 1MB /. | + | |
- | However, to implement two pairs is not a 4MB SIMM modules. | + | |
- | • A pair, each SIMM modules can be implemented 4MB / images or 1MB /. | + | |
- | (You must specify | + | |
- | • B pairs: each SIMM modules can be implemented only 1MB /. | + | |
- | {{:x68000:xsimm10_4.jpg?300|}} | + | *When mounted in slot 1: Height must be less than 15.3mm |
+ | *When mounted in slot 2: Height must be less than 20.4mm | ||
+ | |||
+ | If the size is exceeded, the adjacent slot is unusable. | ||
- | DIP switch settings | + | In addition, when used with the following models, you must have a 1MB of internal memory expansion board in advance |
- | S1 DIP switch settings as pictured above, there are two of S2. The configuration of the projection set at yellow. | + | |
- | - Set to 0: projections to ON (S1, the displays | + | |
- | • 1 set: OFF side protrusion (the number) | + | |
- | (OFF = 1 have been displayed on the board) | + | |
- | DIP switch settings as shown below. | + | |
- | |{{:x68000:xsimm10_5.jpg?250|}} | + | {{:x68000:xsimm10_3_translated.png?300|}} |
- | DIP switch settings, etc., was taken from the instruction manual XSIMM10 Systems Research Inc., Tokyo. | + | XSIMM10 SIMM modules must have the same access time and memory capacity for each pair. The RAM can be expanded up to 10MB maximum. |
- | * The product' | + | SIMM modules with 4MB or 1MB capacity can be used for the first pair. However, do not use 4MB SIMM modules for the second pair. |
+ | *A Pair (Aペア): | ||
+ | *B Pair (Bペア): Both SIMM modules can be only 1MB | ||
+ | |||
+ | **Dipswitch settings** | ||
+ | |||
+ | Click on the following images to enlarge. | ||
+ | |||
+ | |{{: | ||
+ | | OFF = 1 is displayed on the board | S1 and S2 Dipswitch settings as pictured above | | ||
+ | |||
+ | **Configuration examples** | ||
+ | |||
+ | |{{: | ||
+ | | S1 Dipswitch settings | ||
+ | |||
+ | Dipswitch settings were taken from XSIMM10 instruction manual, copyright by Systems Research Ltd., Tokyo. | ||
+ | |||
+ | Keep the scene alive ! | ||
+ | |||
+ | Eidis |
x68000/xsimm10_-_memory_expansion_board.1322855071.txt.gz · Last modified: 2019/08/27 20:44 (external edit)