Differences

This shows you the differences between two versions of the page.

--- x68000:xsimm10_-_memory_expansion_board [2012/01/10 06:51] – eidis
+++ x68000:xsimm10_-_memory_expansion_board [2019/08/27 20:45] (current) – external edit 127.0.0.1
@@ Line 5: / Line 5: @@
 {{:x68000:xsimm10_1.jpg|}}
-XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series expansion slot. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots.
+XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots.
 |{{:x68000:xsimm10_2.jpg|}}  |
 |  XSIMM10  |
-**Selection and implementation of the SIMM module**
+**Compatible SIMM modules**
+The XSIMM10 board can be used with the following commercially available SIMM modules:
+  *PC/AT: 9-bit (with parity) 30-pin
+  *Macintosh: 8-bit, 30-pin
+However, due to the vertical size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions:
+  *When mounted in slot 1: Height must be less than 15.3mm
+  *When mounted in slot 2: Height must be less than 20.4mm
+If the size is exceeded, the adjacent slot is unusable.
+In addition, when used with the following models, you must have a 1MB of internal memory expansion board in advance and a total of 2MB internal memory to add more RAM.
+{{:x68000:xsimm10_3_translated.png?300|}}
+XSIMM10 SIMM modules must have the same access time and memory capacity for each pair. The RAM can be expanded up to 10MB maximum.
+SIMM modules with 4MB or 1MB capacity can be used for the first pair. However, do not use 4MB SIMM modules for the second pair.
-This XSIMM (Single In-line Memory Module) can be installed below the SIMM modules that are commercially available.
+  *A Pair (Ａペア): Both SIMM modules can be 4MB or 1MB (You must specify the capacity of installed SIMM modules).
-For compatible machines • PC / AT: 9 bit (with parity) for the 30-pin Macintosh: 30-pin 8-bit, however, from bandwidth limitations I / O expansion slots, the following restrictions to the size of the SIMM module vertical board The.
+  *B Pair (Bペア): Both SIMM modules can be only 1MB
-• For mounting slot 1: Mounted on the following two slots 15.3mm: below this size exceeds 20.4mm, is that if the adjacent slot unusable.
-In addition, when used with the following models, you must have a total of 2MB internal memory to add more RAM and 1MB of internal memory boards in advance.
-{{:x68000:xsimm10_3.jpg?300|}}
+**Dipswitch settings**
-XSIMM10 one pair of two SIMM modules have the same access time and memory capacity per pair as a pair or two pairs can be expandable to up to 10MB.
+Click on the following images to enlarge.
-SIMM memory modules that can be used per sheet, the sheet is 4MB / images or 1MB /.
-However, to implement two pairs is not a 4MB SIMM modules.
-• A pair, each SIMM modules can be implemented 4MB / images or 1MB /.
-(You must specify the amount of memory on the SIMM module that implements).
-• B pairs: each SIMM modules can be implemented only 1MB /.
-{{:x68000:xsimm10_4.jpg?300|}}
+|{{:x68000:xsimm10_4.jpg?350|}}  |{{:x68000:xsimm10_5_translated.png?350|}}  |
+|  OFF = 1 is displayed on the board  |  S1 and S2 Dipswitch settings as pictured above  |
-DIP switch settings
+**Configuration examples**
-S1 DIP switch settings as pictured above, there are two of S2. The configuration of the projection set at yellow.
-- Set to 0: projections to ON (S1, the displays and S2) that.
-• 1 set: OFF side protrusion (the number) to.
-(OFF = 1 have been displayed on the board)
-DIP switch settings as shown below.
-|{{:x68000:xsimm10_5.jpg?250|}}  |{{:x68000:xsimm10_6.jpg?250|}}  |{{:x68000:xsimm10_7.jpg?250|}}  |
+|{{:x68000:xsimm10_6_translated.png?350|}}  |{{:x68000:xsimm10_7_translated.png?350|}}  |
+|  S1 Dipswitch settings  |  S2 Dipswitch settings  |
-DIP switch settings, etc., was taken from the instruction manual XSIMM10 Systems Research Inc., Tokyo.
+Dipswitch settings were taken from XSIMM10 instruction manual, copyright by Systems Research Ltd., Tokyo.
-* The product's manufacturer, Research Systems, Ltd., Tokyo is.
+Keep the scene alive !
+Eidis