User Tools

Site Tools


x68000:xsimm10_-_memory_expansion_board

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
x68000:xsimm10_-_memory_expansion_board [2012/01/10 09:51] eidisx68000:xsimm10_-_memory_expansion_board [2019/08/27 20:45] (current) – external edit 127.0.0.1
Line 6: Line 6:
  
 XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots. XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots.
- +
 |{{:x68000:xsimm10_2.jpg|}}  | |{{:x68000:xsimm10_2.jpg|}}  |
 |  XSIMM10  | |  XSIMM10  |
  
-**Selection and implementation of the SIMM module**+**Compatible SIMM modules**
  
-This XSIMM (Single In-line Memory Module) board can be used with the following commercially available SIMM modules for compatible machines:+The XSIMM10 board can be used with the following commercially available SIMM modules:
  
   *PC/AT: 9-bit (with parity) 30-pin   *PC/AT: 9-bit (with parity) 30-pin
   *Macintosh: 8-bit, 30-pin   *Macintosh: 8-bit, 30-pin
  
-However, due to the size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions:+However, due to the vertical size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions:
  
-  *When mounted in slot 1: Less than 15.3mm +  *When mounted in slot 1: Height must be less than 15.3mm 
-  *When mounted in slot 2: Less than 20.4mm+  *When mounted in slot 2: Height must be less than 20.4mm
    
 If the size is exceeded, the adjacent slot is unusable. If the size is exceeded, the adjacent slot is unusable.
  
-In addition, when used with the following models, you must have a total of 2MB internal memory to add more RAM and 1MB of internal memory expansion board in advance.+In addition, when used with the following models, you must have a 1MB of internal memory expansion board in advance and a total of 2MB internal memory to add more RAM.
  
 {{:x68000:xsimm10_3_translated.png?300|}} {{:x68000:xsimm10_3_translated.png?300|}}
  
-XSIMM10 SIMM modules must have the same access time and memory capacity as a pair or two pairs. The RAM can be expanded up to 10MB maximum.+XSIMM10 SIMM modules must have the same access time and memory capacity for each pair. The RAM can be expanded up to 10MB maximum.
  
-SIMM modules with 4MB or 1MB capacity can be used as a pair. However, to implement two pairs, do not use 4MB SIMM modules. +SIMM modules with 4MB or 1MB capacity can be used for the first pair. However, do not use 4MB SIMM modules for the second pair
  
-  *A Pair (Aペア): Each SIMM module can be 4MB or 1MB (You must specify the capacity of installed SIMM modules).  +  *A Pair (Aペア): Both SIMM modules can be 4MB or 1MB (You must specify the capacity of installed SIMM modules).  
-  *B Pair (Bペア): Each SIMM module can be only 1MB+  *B Pair (Bペア): Both SIMM modules can be only 1MB
  
-{{:x68000:xsimm10_4.jpg?300|}}+**Dipswitch settings**
  
-**DIP switch settings** +Click on the following images to enlarge.
-  +
-S1 and S2 DIP switch settings as pictured above.+
  
-  *0 = ON  +|{{:x68000:xsimm10_4.jpg?350|}}  |{{:x68000:xsimm10_5_translated.png?350|}}  |   
-  *1 = OFF+ OFF = 1 is displayed on the board  |  S1 and S2 Dipswitch settings as pictured above  |
  
-(OFF = 1 have been displayed on the board)  +**Configuration examples**
-DIP switch settings as shown below.+
  
-|{{:x68000:xsimm10_5.jpg?250|}}  |{{:x68000:xsimm10_6.jpg?250|}}  |{{:x68000:xsimm10_7.jpg?250|}}  |+|{{:x68000:xsimm10_6_translated.png?350|}}  |{{:x68000:xsimm10_7_translated.png?350|}}  | 
 + S1 Dipswitch settings  |  S2 Dipswitch settings  |
  
-DIP switch settings, etc., was taken from the instruction manual XSIMM10 Systems Research Inc., Tokyo. +Dipswitch settings were taken from XSIMM10 instruction manual, copyright by Systems Research Ltd., Tokyo. 
  
-* The product's manufacturer, Research Systems, Ltd., Tokyo is.+Keep the scene alive !
  
 +Eidis
x68000/xsimm10_-_memory_expansion_board.1326153080.txt.gz · Last modified: 2019/08/27 20:44 (external edit)