arcade:joystick_mechs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
arcade:joystick_mechs [2023/12/31 10:06] – [Sanwa] NFG | arcade:joystick_mechs [2024/05/03 15:17] – NFG | ||
---|---|---|---|
Line 1: | Line 1: | ||
===== Joystick Mechanisms ===== | ===== Joystick Mechanisms ===== | ||
Just a fun-filled list of joystick mounts for easy fact finding. | Just a fun-filled list of joystick mounts for easy fact finding. | ||
+ | |||
+ | ===== Pinouts ===== | ||
+ | Most of the joysticks listed below use either spade connectors (AT-187 Japan size) or a 5-pin JST NH-series connector. | ||
+ | |||
+ | But you can't hurt anything by wiring these up wrong, so if you're not sure, go ahead and experiment. | ||
+ | |||
+ | The connector used for Sanwa and Seimitsu sticks is a **JST NH-series** 5-pin. | ||
+ | |||
+ | {{: | ||
+ | ^ Pin ^ LS-33 ^ Seimitsu | ||
+ | | 1 | Down | **GND** | ||
+ | | 2 | Right | Left (1 CCW) | Down (1 CW) | | ||
+ | | 3 | **GND** | Right (2 CW) | Right (2 CW) | | ||
+ | | 4 | Up | Down (1 CW) | Left | | ||
+ | | 5 | Left | Up (2 CCW) | **GND** | ||
+ | |||
+ | As a result, I can't claim this is totally accurate, though I believe it is. There' | ||
+ | |||
+ | The Namco pinout is correct, based on a connector on the RIGHT side, if you're looking from the top of the control panel. | ||
+ | |||
+ | (Image shamelessly yanked from JST's documentation) | ||
+ | |||
+ | | | ||
+ | ^ Housing | H5P-SHF-AA | ||
+ | ^ Contact (28-22 AWG) | SHF-001T-0.8BS | ||
+ | ^ Contact (30-28 AWG) | SHF-002T-0.8BS | ||
===== Seimitsu ===== | ===== Seimitsu ===== | ||
Line 22: | Line 48: | ||
* LS-56 | * LS-56 | ||
* LS-55 | * LS-55 | ||
+ | * LS-33 | ||
==== Seimitsu 50mm Mechs ==== | ==== Seimitsu 50mm Mechs ==== | ||
Line 32: | Line 59: | ||
SNK's home consoles used Seimitsu mechs (or clones of them) with a 40mm pattern. | SNK's home consoles used Seimitsu mechs (or clones of them) with a 40mm pattern. | ||
- | These same mechs (or clones of them) were also used in sticks from Sigma and (IIRC) ASCII. | + | These same mechs (or clones of them) were also used in sticks from Sigma (The Σ-2200 definitely used a Seimitsu mech) and (IIRC) ASCII. |
{{: | {{: | ||
===== Sanwa ===== | ===== Sanwa ===== | ||
- | Sanwa' | + | Sanwa' |
- | The two 65mm holes are not threaded, and typically use a nut & bolt attachment. | + | {{ : |
- | Sanwa sticks are mounted deeper into the panel compared to Seimitsu sticks. | + | The two 65mm holes in both the JLX and JLF are not threaded, and typically use a nut & bolt attachment. |
+ | |||
+ | The JLF 4-hole mounts are plastic and use self-tapping counter-sink screws to fix the mech to the plate. The JLX sticks however use threaded metal inserts, and so must use different screws than the JLF mechs. | ||
+ | |||
+ | Sanwa sticks are mounted deeper into the panel compared to Seimitsu sticks. | ||
Sanwa sticks use a raised central circle around the pivot, to allow for the pivot to rise vertically above the nominal surface of the stick. | Sanwa sticks use a raised central circle around the pivot, to allow for the pivot to rise vertically above the nominal surface of the stick. | ||
===== Hori ===== | ===== Hori ===== | ||
- | Hori's made many mechs throughout their history. | + | Hori's made many mechs throughout their history. |
{{: | {{: | ||
- | The Hayabusa shown above includes the mounting plate. | + | The Hayabusa shown above includes the mounting plate. |
+ | |||
+ | [[Hori Hayabusa|Hori Hayabusa Info Page]] | ||
===== ASCII ===== | ===== ASCII ===== | ||
Line 62: | Line 95: | ||
This mech is compatible with Sanwa JLF mounts and accessories. | This mech is compatible with Sanwa JLF mounts and accessories. | ||
+ | |||
+ | ===== Nintendo ===== | ||
+ | Back in the 80s, with Donkey Kong and Popeye, the Vs cabinets, and even R-Type (which Nintendo distributed in North America) Nintendo used an all-metal joystick that was small, clicky, had an incredibly short throw, and a very short shaft. | ||
+ | |||
arcade/joystick_mechs.txt · Last modified: 2024/06/21 00:10 by NFG