preface:why_x68000_s_caps_are_almost_broken
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionNext revisionBoth sides next revision | ||
preface:why_x68000_s_caps_are_almost_broken [2014/07/28 01:14] – created a24tanabe | preface:why_x68000_s_caps_are_almost_broken [2014/09/17 06:09] – [Compact XVI,030 Compact] eidis | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Why X68000' | ||
+ | |||
In 1980s, aluminum electrolytic capacitors with quaternary salt were used. | In 1980s, aluminum electrolytic capacitors with quaternary salt were used. | ||
It was said high performance and long life. Many companies made them. | It was said high performance and long life. Many companies made them. | ||
Line 16: | Line 18: | ||
Any advices is welcome. | Any advices is welcome. | ||
- | p.s. Original X68000 PSU seems not to use quaternary salt. But they are too old, so they should be replaced. | + | p.s. Original X68000 PSU seems not to use quaternary salt. But they are too old, so they should be replaced. |
+ | |||
+ | ====== Original model ====== | ||
+ | |||
+ | ====== ACE (SH2 Unit) ====== | ||
+ | |||
+ | It has the same design as the PSU of Expert but features lower rated capacitors. It is recommended to use use the capacitor ratings which are mentioned in the Expert section. | ||
+ | |||
+ | ====== EXPERT, | ||
+ | |||
+ | Almost all info taken from: http:// | ||
+ | |||
+ | All X68000 power supplies fail because of the capacitors. Here are a few common symptoms and solutions: | ||
+ | |||
+ | - Main power is connected, front LED is glowing red but the system does not react to front soft-power switch. Check if ZD31 or anything around it is burnt. Replace ZD31 and all electrolytic capacitors. There are some cases when Q32 also needs to be replaced. In some rare cases PC31, PC51, PC52 also need to be replaced. | ||
+ | -R35 rupture is caused when C31 capacity has decreased to the point that it is no longer able to supply constant voltage and current. In this case it is advisable to replace Q31, Q32, R35, ZD31. | ||
+ | -The fuse gets blown if C9 is faulty. Replace all electrolytic capacitors, 4A fuse and check if there are no signs of damage to the ZD31 or near it. | ||
+ | -Most parts though discontinued have generic replacements available. The only custom-made part is the transformer but it is very reliable and does not break easily. | ||
+ | |||
+ | **Schematics** | ||
+ | *[[http:// | ||
+ | |||
+ | ^Part number | ||
+ | |F1 |125V 4A fuse |(MZ) small type | | ||
+ | |ZD31 |[[http:// | ||
+ | |ZD32 |[[http:// | ||
+ | |ZD51 |[[http:// | ||
+ | |PC31, PC51 |[[http:// | ||
+ | |PC52 |[[http:// | ||
+ | |Q31 |[[http:// | ||
+ | |Q32, Q33, Q53 |[[http:// | ||
+ | |C9 |200V 470μF | ||
+ | |C24 |25V 1000μF | ||
+ | |C25 |16V 1000μF | ||
+ | |C27 |25V 220μF | ||
+ | |C28 |16V 100μF | ||
+ | |C31 |16V 100μF | ||
+ | |C33 |16V 220μF | ||
+ | |C34 |10V 100μF | ||
+ | |C35 |50V 10μF |Original: 25V 10μF | | ||
+ | |C38 |50V 3.3μF | ||
+ | |C40, C41 |16V 6800μF | ||
+ | |C42 |10V 2200μF | ||
+ | |R33, R34 |100Ω 1/6W | | | ||
+ | |R35 |3Ω 1/4W |Original: 3.3Ω | | ||
+ | |R40 |2KΩ 1/6W | | | ||
+ | |R98 |2.2KΩ 1/4W |Original: 1/6W | | ||
+ | |||
+ | ====== PRO ====== | ||
+ | |||
+ | **Schematics** | ||
+ | *[[http:// | ||
+ | |||
+ | ====== Compact XVI,030 Compact ====== | ||
+ | |||
+ | These are more tolerant. Their capacitors leak but usually do not kill anything and a simple recap is all that is needed. |
preface/why_x68000_s_caps_are_almost_broken.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1