x68000:cz-6bs1_-_genuine_sharp_scsi_board
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/03 05:02] – created eidis | x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/12 00:44] – eidis | ||
---|---|---|---|
Line 5: | Line 5: | ||
{{: | {{: | ||
- | SCSI genuine Sharp Corporation | + | This is a genuine Sharp Corporation |
- | The initial specification | + | |
{{: | {{: | ||
- | 1. Product Overview | + | **1. Product Overview** |
- | 1-1 Overview This board is a personal workstation series | + | 1-1 Overview |
- | (Small computer system interface - → SCSl (Smail | + | |
- | Mass Storage | + | This board is made for X68000 |
- | Beteta | + | Small Computer System Interface |
+ | |||
+ | 1-2 Features | ||
+ | |||
+ | *Mass Storage | ||
+ | | ||
- | 2. Product configuration | + | **2. Package contents** |
- | When removed from the packing case, when Kuta make sure that you have shipped | + | When unboxed, make sure that you have received |
- | SCSl software | + | * SCSI brackets |
- | □ List your consult your instruction book window | + | * Floppy disk with SCSI software |
- | Carton ●, packaging materials, please have a safe place. | + | |
- | For example, during reshipment ● Please use Ganarazu failure. | + | * Instruction manual |
+ | * Waranty voucher | ||
+ | * List of customer services | ||
- | 3. Notes on installation issues for flights | + | Please keep packaging materials in safe place. |
- | When installing the computer to Podo ● This instruction manual that came with the computer " | + | **3. Installation notes** |
- | ● When using the Podo book, when read in conjunction Kuta instruction manual of the device SCSl. | + | |
- | When not in use for long ●, Podo remove this from the computer when to protect it from ESD connector into the supplied anti-static bag. | + | |
- | Should ●, and discontinue use when you feel a failure or abnormal gil of purchase, when you Kuta consult your nearest office or contact us. | + | |
- | (Please note in particular our point). | + | |
- | SCSI interface and CZ ● hard disk interface - at × 68000 series except for the 623C, the interface of hard Gita with far different and specifications SCSl interface on Human68k is not arrived there as an interface of another system that interfaces the two . In hard disks and hard disks connected to the SOSl interface is connected to a hard disk interface is a far different representations, | + | |
- | The former hard simply (at sign HD0 ~ HD15) and represent the case of the latter device or hard SCSl (at sign SCSl0 ~ SCSl7) and is expressed. | + | |
- | (" | + | |
- | SCSl ● ID numbers for hard disk interface and the interface is so physically different interfaces as described above, up to 16 hard disk interface (No. 0 to No. 15 from the device number), up to a maximum of seven SCSl interface (lD No. 6 from No. 0 to No.) No. 23 devices can be connected to the total. | + | |
- | Takemasu was used without problems even among the same number of the device ID number that is connected to the interface SCSl lD number of devices that are connected to the hard disk interface Tay. | + | |
- | 4. Names and handling procedures | + | *When installing SCSI bracket pay attention to which one you need, because desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C have different dimensions. Switch the power switch to " |
+ | *Use this device only after installing the bracket and reading the instruction manual which came with your SCSI device. | ||
+ | *When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | ||
+ | *If the device has stopped working, please contact the nearest customer service center. | ||
+ | *The SCSI interface and X68000 integrated SASI interface, except for the CZ-623C, is different and SCSI interface is seen by Human68k as another interface that can interchange data betwean both interfaces. Devices which are connected to SASI interface and those which are connected to SCSI have different representation ID's. For example, SASI (HD0 - HD15) and SCSI (SCSI0 - SCSI7). Device may be marked with ID that it represents. | ||
+ | *ID numbers for SCSI and SASI devices differ and they are physically different interfaces. As described above, SASI can handle up to 16 devices, SCSI can handle up to a maximum of 7 devices. A maximum of 23 devices can be connected in total. | ||
+ | This board was used without problems even after connecting the same amount of devices to SCSI and SASI interface at the same time. | ||
+ | |||
+ | **4. Names and handling procedures** | ||
4-1 Names of Parts | 4-1 Names of Parts | ||
- | {{: | + | {{: |
+ | |||
+ | 4-2 Jumper settings | ||
+ | |||
+ | Jumpers JP1, JP2 set the interrupt priority for 68000MPU to level 2 or 4 (Source I/0 is available in two levels) and the board interprets from the jumper settings which one to use. Factory default is set to level 2. If you own the software, interrupt handling is set as follows. | ||
+ | Set the priority level of the interrupt request signal with jumper JP2, set the interrupt priority level of the allowed signal with jumper JP1. The priority level can be selected as Level 2 or Level 4. | ||
+ | |||
+ | | | JP1 | JP2 | | ||
+ | | Level 2 | 1-2 | 1-2 | | ||
+ | | Level 4 | 2-3 | 2-3 | | ||
+ | |||
+ | Kernel-level priority interrupt request signal will be activated and allowed signal will be set to the same level. | ||
+ | Both jumpers must be set at the same level. | ||
+ | |||
+ | 4-3 Compatible X68000 hardware | ||
+ | |||
+ | *When used in tower models such as CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C the device must be installed in I/0 slot 2. If you are planing to use the CZ-6BS1 in conjunction with CZ-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-6BC1, please populate I/O slot 1 before installing this board. This board can also be used in conjunction with CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-6BN1 boards. | ||
+ | *For desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C please install the device in I/O slot 4. Since the introduction of I/O expansion box (CZ-6EB1) we ship two brackets. Please use the appropriate. However the bracket can not be used in CZ-600C, CZ-601C, CZ-611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C alongside with CZ-6BF1, CZ-6BM1, CZ-6BC1 when combined with this board. | ||
- | Switch JP1 jumper setting on the switch on hoard 4-2, JP2 interrupt priority level 2 and 4 as 68000MP ∪ He interrupts (from the I / 0 Surotsuto are two levels available) Set whether to use either This switch is used to. The included software interrupt processing in the setting of the switch so jacket does not use is optional. (Factory default is set to level 2 for a bottle.) | + | " |
- | If you own a software interrupt processing is set as follows. | + | |
- | Set the priority level of the interrupt request signal switch jacket JP2, set the interrupt priority level of the signal allowed by the jacket Switch JP1. The priority level can be selected as a Level 2 or Level 4. | + | |
- | | |JP1 Setting | + | {{: |
x68000/cz-6bs1_-_genuine_sharp_scsi_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1