x68000:cz-6bs1_-_genuine_sharp_scsi_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/10 21:50] – eidis | x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/20 03:27] – eidis | ||
---|---|---|---|
Line 11: | Line 11: | ||
**1. Product Overview** | **1. Product Overview** | ||
- | 1-1 This board is made for X68000 personal workstation series (except CZ-623) and is attached to I/0 expansion slot. It can be used with SCSI MO drives, hard disks or CD-ROM/RW units. | + | 1-1 Overview |
- | Smail Computer System Interface (SCSI) is the standard for the exchange | + | |
- | Mass Storage device with the features of Hue ● SCSl 1-2 Inter: a magneto-optical disks as part Unicast, such as hard disk unit can connect | + | This board is made for X68000 personal workstation series (except CZ-623) and is attached to I/0 expansion slot. It can be used with SCSI MO drives, hard disks or CD-ROM/RW units. |
- | Beteta | + | Small Computer System Interface (SCSI) is the standard for data exchange between computer systems and peripherals. |
+ | |||
+ | 1-2 Features | ||
+ | |||
+ | *Mass Storage Device with SCSI interface: up to seven devices can be connected in daisy-chain. | ||
+ | | ||
- | **2. Product configuration** | + | **2. Package contents** |
- | When removed from the packing case, when Kuta make sure that you have shipped | + | When unboxed, make sure that you have received |
- | SCSl software | + | * SCSI brackets |
- | □ List your consult your instruction book window | + | * Floppy disk with SCSI software |
- | Carton ●, packaging materials, please have a safe place. | + | |
- | For example, during reshipment ● Please use Ganarazu failure. | + | * Instruction manual |
+ | * Waranty voucher | ||
+ | * List of customer services | ||
- | **3. Notes on installation issues for flights** | + | Please keep packaging materials in safe place. |
- | When installing | + | **3. Installation notes** |
- | ● When using the Podo book, when read in conjunction Kuta instruction manual | + | |
- | When not in use for long ●, Podo remove | + | *When installing |
- | Should ●, and discontinue use when you feel a failure or abnormal gil of purchase, when you Kuta consult your nearest | + | *Use this device only after installing the bracket and reading |
- | (Please note in particular our point). | + | *When not in use for long periods of time, remove the device from computer |
- | SCSI interface and CZ ● hard disk interface | + | *If the device has stopped working, please contact the nearest |
- | The former hard simply | + | |
- | (" | + | *ID numbers for SCSI and SASI devices differ and they are physically different interfaces. As described above, |
- | SCSl ● ID numbers for hard disk interface | + | This board was used without problems even after connecting |
- | Takemasu | + | |
**4. Names and handling procedures** | **4. Names and handling procedures** | ||
Line 41: | Line 48: | ||
4-1 Names of Parts | 4-1 Names of Parts | ||
- | {{: | + | {{: |
+ | |||
+ | 4-2 Jumper settings | ||
+ | |||
+ | Jumpers JP1, JP2 set the interrupt priority for 68000 CPU to level 2 or 4 (Source I/0 is available in two levels) and the board interprets from the jumper settings which one to use. Factory default is set to level 2. If you own the software, interrupt handling is set as follows. | ||
+ | Set the priority level of the interrupt request signal with jumper JP2, set the interrupt priority level of the allowed signal with jumper JP1. The priority level can be selected as Level 2 or Level 4. | ||
- | Switch | + | | | |
- | If you own a software interrupt processing is set as follows. | + | | Level 2 |
- | Set the priority level of the interrupt request signal switch jacket JP2, set the interrupt priority level of the signal allowed by the jacket Switch JP1. The priority level can be selected as a Level 2 or Level 4. | + | | |
- | | |JP1 Setting | + | Kernel-level priority interrupt request signal will be activated and allowed signal will be set to the same level. |
- | |If you use a Level 2 |1-2 jumper inserted between | + | Both jumpers must be set at the same level. |
- | |If you use four Rebaru | + | |
- | Kyung-level priority interrupt request signal will be activated and allowed is set to the same level. | + | 4-3 Compatible X68000 hardware |
- | At level 2 interrupt request level, such as how to use it at level 4 and level interrupt is not allowed. | + | |
- | Attached to a 4-3 X68000 series ● CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C installed in the case of the connector and attach to the l / 0 slot 2 again. | + | *When used in tower models such as CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C |
- | CZ is already for sale ※-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-board and 6BC1 (CZ-6BS1) If the combination is, I make sure before you install this board Please attach to / O slot 1. | + | *For desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C please |
- | (CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-board such as 6BN1 is in relation to the connector, in conjunction with this board please note that you can.) | + | |
- | ● CZ-652C, CZ-653C, CZ-662C, CZ-663C | + | |
- | The board that use of the ※ I / O slot cover, | + | |
- | However, for the computer (CZ-600C, CZ-601C, CZ-611C, CZ-602C, CZ-612C, CZ-603C, CZ-for 613C) I / O slot cover, | + | |
" | " | ||
- | {{: | + | {{: |
x68000/cz-6bs1_-_genuine_sharp_scsi_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1