x68000:cz-6bs1_-_genuine_sharp_scsi_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 00:26] – eidis | x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 22:27] – eidis | ||
---|---|---|---|
Line 14: | Line 14: | ||
This board is made for X68000 personal workstation series (except CZ-623) and is attached to I/0 expansion slot. It can be used with SCSI MO drives, hard disks or CD-ROM/RW units. | This board is made for X68000 personal workstation series (except CZ-623) and is attached to I/0 expansion slot. It can be used with SCSI MO drives, hard disks or CD-ROM/RW units. | ||
- | Smail Computer System Interface (SCSI) is the standard for data exchange between computer systems and peripherals. | + | Small Computer System Interface (SCSI) is the standard for data exchange between computer systems and peripherals. |
1-2 Features | 1-2 Features | ||
Line 36: | Line 36: | ||
**3. Installation notes** | **3. Installation notes** | ||
- | *When installing SCSI bracket pay attention to which one you need, because desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C have different dimensions. Switch the power switch to " | + | *When installing SCSI bracket pay attention to which one you need, because desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C have different dimensions. Switch the power switch to " |
*Use this device only after installing the bracket and reading the instruction manual which came with your SCSI device. | *Use this device only after installing the bracket and reading the instruction manual which came with your SCSI device. | ||
*When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | *When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | ||
- | Should | + | |
- | | + | |
- | (Please note in particular our point). | + | *ID numbers for SCSI and SASI devices differ and they are physically different interfaces. As described above, |
- | SCSI interface and CZ ● hard disk interface | + | This board was used without problems even after connecting |
- | The former hard simply | + | |
- | (" | + | |
- | SCSl ● ID numbers for hard disk interface | + | |
- | Takemasu | + | |
**4. Names and handling procedures** | **4. Names and handling procedures** | ||
Line 54: | Line 50: | ||
{{: | {{: | ||
- | Switch JP1 jumper setting on the switch on hoard 4-2, JP2 interrupt priority level 2 and 4 as 68000MP ∪ He interrupts (from the I / 0 Surotsuto are two levels available) Set whether to use either This switch is used to. The included software interrupt processing in the setting of the switch so jacket does not use is optional. (Factory default is set to level 2 for a bottle.) | + | 4-2 Jumper settings |
- | If you own a software interrupt processing is set as follows. | + | |
- | Set the priority level of the interrupt request signal switch jacket JP2, set the interrupt priority level of the signal allowed by the jacket Switch JP1. The priority level can be selected as a Level 2 or Level 4. | + | |
- | | |JP1 Setting | + | Jumpers |
- | |If you use a Level 2 |1-2 jumper inserted between | + | Set the priority level of the interrupt request signal with jumper |
- | |If you use four Rebaru | + | |
- | Kyung-level priority interrupt request signal will be activated and allowed | + | | | JP1 | JP2 | |
- | At level 2 interrupt request | + | | Level 2 | 1-2 | 1-2 | |
+ | | Level 4 | 2-3 | 2-3 | | ||
+ | |||
+ | Kernel-level priority interrupt request signal will be activated and allowed | ||
+ | Both jumpers must be set at the same level. | ||
+ | |||
+ | 4-3 Compatible X68000 hardware | ||
+ | |||
+ | *When used in CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C the device must be installed in I/0 slot 2. If you are planing | ||
- | Attached to a 4-3 X68000 series ● CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C installed in the case of the connector and attach to the l / 0 slot 2 again. | ||
- | CZ is already for sale ※-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-board and 6BC1 (CZ-6BS1) If the combination is, I make sure before you install this board Please attach to / O slot 1. | ||
- | (CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-board such as 6BN1 is in relation to the connector, in conjunction with this board please note that you can.) | ||
● CZ-652C, CZ-653C, CZ-662C, CZ-663C installed in the case, please attach to the I / 0 slot 4. | ● CZ-652C, CZ-653C, CZ-662C, CZ-663C installed in the case, please attach to the I / 0 slot 4. | ||
The board that use of the ※ I / O slot cover, I / O expansion box for the base unit and a computer (CZ-6EB1) because we have two ships with a slot cover for the slot corresponding to each Please use the cover. | The board that use of the ※ I / O slot cover, I / O expansion box for the base unit and a computer (CZ-6EB1) because we have two ships with a slot cover for the slot corresponding to each Please use the cover. |
x68000/cz-6bs1_-_genuine_sharp_scsi_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1