x68000:cz-6bs1_-_genuine_sharp_scsi_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 01:06] – eidis | x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 22:27] – eidis | ||
---|---|---|---|
Line 36: | Line 36: | ||
**3. Installation notes** | **3. Installation notes** | ||
- | *When installing SCSI bracket pay attention to which one you need, because desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C have different dimensions. Switch the power switch to " | + | *When installing SCSI bracket pay attention to which one you need, because desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C have different dimensions. Switch the power switch to " |
*Use this device only after installing the bracket and reading the instruction manual which came with your SCSI device. | *Use this device only after installing the bracket and reading the instruction manual which came with your SCSI device. | ||
*When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | *When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | ||
*If the device has stopped working, please contact the nearest customer service center. | *If the device has stopped working, please contact the nearest customer service center. | ||
- | *The SCSI interface and X68000 integrated SASI interface, except for the CZ-623C, is different and SCSI interface is seen by Human68k as another interface that can interchange data betwean both interfaces. | + | *The SCSI interface and X68000 integrated SASI interface, except for the CZ-623C, is different and SCSI interface is seen by Human68k as another interface that can interchange data betwean both interfaces. |
- | The former hard simply | + | *ID numbers for SCSI and SASI devices differ and they are physically different interfaces. As described above, |
- | (" | + | This board was used without problems even after connecting |
- | SCSl | + | |
- | + | ||
- | ● ID numbers for hard disk interface | + | |
- | Takemasu | + | |
**4. Names and handling procedures** | **4. Names and handling procedures** | ||
Line 54: | Line 50: | ||
{{: | {{: | ||
- | Switch JP1 jumper setting on the switch on hoard 4-2, JP2 interrupt priority level 2 and 4 as 68000MP ∪ He interrupts | + | 4-2 Jumper settings |
- | If you own a software interrupt | + | |
- | Set the priority level of the interrupt request signal | + | Jumpers JP1, JP2 set the interrupt priority |
+ | Set the priority level of the interrupt request signal | ||
+ | |||
+ | | | JP1 | JP2 | | ||
+ | | Level 2 | 1-2 | 1-2 | | ||
+ | | Level 4 | 2-3 | 2-3 | | ||
+ | |||
+ | Kernel-level priority interrupt request signal will be activated and allowed signal will be set to the same level. | ||
+ | Both jumpers must be set at the same level. | ||
- | | |JP1 Setting | + | 4-3 Compatible X68000 hardware |
- | |If you use a Level 2 |1-2 jumper inserted between the socket | + | |
- | |If you use four Rebaru | + | |
- | Kyung-level priority interrupt request signal will be activated and allowed is set to the same level. | + | *When used in CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C the device must be installed in I/0 slot 2. If you are planing |
- | At level 2 interrupt request level, such as how to use it at level 4 and level interrupt is not allowed. | + | |
- | Attached to a 4-3 X68000 series ● CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C installed in the case of the connector and attach to the l / 0 slot 2 again. | ||
- | CZ is already for sale ※-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-board and 6BC1 (CZ-6BS1) If the combination is, I make sure before you install this board Please attach to / O slot 1. | ||
- | (CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-board such as 6BN1 is in relation to the connector, in conjunction with this board please note that you can.) | ||
● CZ-652C, CZ-653C, CZ-662C, CZ-663C installed in the case, please attach to the I / 0 slot 4. | ● CZ-652C, CZ-653C, CZ-662C, CZ-663C installed in the case, please attach to the I / 0 slot 4. | ||
The board that use of the ※ I / O slot cover, I / O expansion box for the base unit and a computer (CZ-6EB1) because we have two ships with a slot cover for the slot corresponding to each Please use the cover. | The board that use of the ※ I / O slot cover, I / O expansion box for the base unit and a computer (CZ-6EB1) because we have two ships with a slot cover for the slot corresponding to each Please use the cover. |
x68000/cz-6bs1_-_genuine_sharp_scsi_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1