x68000:cz-6bs1_-_genuine_sharp_scsi_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 01:14] – eidis | x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/12 00:44] – eidis | ||
---|---|---|---|
Line 40: | Line 40: | ||
*When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | *When not in use for long periods of time, remove the device from computer and put it into the supplied anti-static bag to protect it from electro static discharge. | ||
*If the device has stopped working, please contact the nearest customer service center. | *If the device has stopped working, please contact the nearest customer service center. | ||
- | *The SCSI interface and X68000 integrated SASI interface, except for the CZ-623C, is different and SCSI interface is seen by Human68k as another interface that can interchange data betwean both interfaces. | + | *The SCSI interface and X68000 integrated SASI interface, except for the CZ-623C, is different and SCSI interface is seen by Human68k as another interface that can interchange data betwean both interfaces. |
- | + | *ID numbers for SCSI and SASI devices differ | |
- | ● ID numbers for hard disk interface | + | This board was used without problems even after connecting |
- | Takemasu | + | |
**4. Names and handling procedures** | **4. Names and handling procedures** | ||
Line 49: | Line 48: | ||
4-1 Names of Parts | 4-1 Names of Parts | ||
- | {{: | + | {{: |
+ | |||
+ | 4-2 Jumper settings | ||
+ | |||
+ | Jumpers JP1, JP2 set the interrupt priority for 68000MPU to level 2 or 4 (Source I/0 is available in two levels) and the board interprets from the jumper settings which one to use. Factory default is set to level 2. If you own the software, interrupt handling is set as follows. | ||
+ | Set the priority level of the interrupt request signal with jumper JP2, set the interrupt priority level of the allowed signal with jumper JP1. The priority level can be selected as Level 2 or Level 4. | ||
- | Switch | + | | | |
- | If you own a software interrupt processing is set as follows. | + | | Level 2 |
- | Set the priority level of the interrupt request signal switch jacket JP2, set the interrupt priority level of the signal allowed by the jacket Switch JP1. The priority level can be selected as a Level 2 or Level 4. | + | | |
- | | |JP1 Setting | + | Kernel-level priority interrupt request signal will be activated and allowed signal will be set to the same level. |
- | |If you use a Level 2 |1-2 jumper inserted between | + | Both jumpers must be set at the same level. |
- | |If you use four Rebaru | + | |
- | Kyung-level priority interrupt request signal will be activated and allowed is set to the same level. | + | 4-3 Compatible X68000 hardware |
- | At level 2 interrupt request level, such as how to use it at level 4 and level interrupt is not allowed. | + | |
- | Attached to a 4-3 X68000 series ● CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C installed in the case of the connector and attach to the l / 0 slot 2 again. | + | *When used in tower models such as CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C |
- | CZ is already for sale ※-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-board and 6BC1 (CZ-6BS1) If the combination is, I make sure before you install this board Please attach to / O slot 1. | + | *For desktop models such as CZ-652C, CZ-653C, CZ-662C, CZ-663C please |
- | (CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-board such as 6BN1 is in relation to the connector, in conjunction with this board please note that you can.) | + | |
- | ● CZ-652C, CZ-653C, CZ-662C, CZ-663C | + | |
- | The board that use of the ※ I / O slot cover, | + | |
- | However, for the computer (CZ-600C, CZ-601C, CZ-611C, CZ-602C, CZ-612C, CZ-603C, CZ-for 613C) I / O slot cover, | + | |
" | " | ||
- | {{: | + | {{: |
x68000/cz-6bs1_-_genuine_sharp_scsi_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1