Differences

This shows you the differences between two versions of the page.

--- x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 04:40] – eidis
+++ x68000:cz-6bs1_-_genuine_sharp_scsi_board [2011/12/11 22:27] – eidis
@@ Line 52: / Line 52: @@
 -2 Jumper settings
-Jumpers JP1, JP2 set the interrupt priority level for 68000MPU to 2 or 4. (from the I/0 Surotsuto is available in two levels) switches for setting whether to use either. The included software interrupt processing in the setting of the switch so jacket does not use is optional. (Factory default is set to level 2 for a bottle.)If you own a software interrupt processing is set as follows.
+Jumpers JP1, JP2 set the interrupt priority for 68000MPU to level 2 or 4 (Source I/0 is available in two levels) and the board interprets from the jumper settings which one to use. Factory default is set to level 2. If you own the software, interrupt handling is set as follows.
-Set the priority level of the interrupt request signal switch jacket JP2, set the interrupt priority level of the signal allowed by the jacket Switch JP1. The priority level can be selected as a Level 2 or Level 4.
+Set the priority level of the interrupt request signal with jumper JP2, set the interrupt priority level of the allowed signal with jumper JP1. The priority level can be selected as Level 2 or Level 4.
-|  |JP1 Setting  |JP2 setting  |
+|  |  JP1  |  JP2  |
-|If you use Level 2  |1-2 jumper inserted between the socket  |1-2 jumper inserted between the socket  |
+|  Level 2  |  1-2  |  1-2  |
-|If you use Level 4  |2-3 jumper inserted between the socket  |2-3 jumper inserted between the socket  |
+|  Level 4  |  2-3  |  2-3  |
-Kyung-level priority interrupt request signal will be activated and allowed is set to the same level.
+Kernel-level priority interrupt request signal will be activated and allowed signal will be set to the same level.
-At level 2 interrupt request level, such as how to use it at level 4 and level interrupt is not allowed.
+Both jumpers must be set at the same level.
+-3 Compatible X68000 hardware
+  *When used in CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C the device must be installed in I/0 slot 2. If you are planing to use the CZ-6BS1 in conjunction with CZ-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-6BC1, please populate I/O slot 1 before installing this board. This board can also be used in conjunction with CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-6BN1 boards.
-Attached to a 4-3 X68000 series ● CZ-600C, CZ-601C, CZ611C, CZ-602C, CZ-612C, CZ-603C, CZ-613C installed in the case of the connector and attach to the l / 0 slot 2 again.
-CZ is already for sale ※-6BE2, CZ-6BE4, CZ-6BF1, CZ-6BM1, CZ-6BP1, CZ-board and 6BC1 (CZ-6BS1) If the combination is, I make sure before you install this board Please attach to / O slot 1.
-(CZ-6BG1, CZ-6BU1, CZ-6BL1, CZ-6BL2, CZ-board such as 6BN1 is in relation to the connector, in conjunction with this board please note that you can.)
 ● CZ-652C, CZ-653C, CZ-662C, CZ-663C installed in the case, please attach to the I / 0 slot 4.
 The board that use of the ※ I / O slot cover, I / O expansion box for the base unit and a computer (CZ-6EB1) because we have two ships with a slot cover for the slot corresponding to each Please use the cover.