x68000:hard_drive_on_sasi_machine
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:hard_drive_on_sasi_machine [2014/06/30 04:58] – [Chapter 3: Preparing the Master floppy] eidis | x68000:hard_drive_on_sasi_machine [2019/08/27 20:45] – external edit 127.0.0.1 | ||
---|---|---|---|
Line 2: | Line 2: | ||
Using a SCSI to IDE/CF/SD adaptor as a hard drive on X68000 hardware. | Using a SCSI to IDE/CF/SD adaptor as a hard drive on X68000 hardware. | ||
- | Six devices are detailed below: | + | Seven devices are detailed below: |
- | * I-O Data IDSC21-E | + | * I-O Data [[http:// |
- | * Yamaha V769970 | + | * Yamaha |
- | * Acard AEC-7720U | + | * Acard [[http:// |
- | * I-O Data R-IDSC-E/ | + | * I-O Data [[http:// |
- | * STRATOS CF AztecMonster | + | * STRATOS |
- | * code/src designs SCSI2SD | + | * code/src designs |
+ | * Classic PC Rescue Committee [[http:// | ||
Most of them were tested on an ACE-HD system, but compatibility for all X68000 should be the same. | Most of them were tested on an ACE-HD system, but compatibility for all X68000 should be the same. | ||
Line 52: | Line 53: | ||
{{: | {{: | ||
- | **SCSI2SD** is an open hardware and open source project by [[http:// | + | **SCSI2SD** is an open hardware and open source project by [[http:// |
+ | |||
+ | For **SCSI2SD** the following settings were used: | ||
+ | * SCSI ID3 | ||
+ | * Termination On | ||
+ | * Parity Off | ||
{{: | {{: | ||
+ | |||
+ | **CLPC-CFSxSI101** is special because it is the only one which can be used in native SASI or SCSI mode. All previous adapters only work in SCSI mode. It is made in Japan, works with CF cards and can be purchased from [[http:// | ||
+ | |||
+ | {{: | ||
==== Chapter 2 Connecting the hardware ==== | ==== Chapter 2 Connecting the hardware ==== | ||
Line 89: | Line 99: | ||
Download DiskExplorer and the disk image transfer tool for your operating system. | Download DiskExplorer and the disk image transfer tool for your operating system. | ||
- | * [[http:// | + | * [[http:// |
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
Line 97: | Line 107: | ||
==== Chapter 4: SASI strikes back ==== | ==== Chapter 4: SASI strikes back ==== | ||
+ | |||
+ | **Note for SCSI users:** SUPER, XVI, XVI Compact, X68030, X68030 Compact do not need the SxSI driver and installation of bootloader to SRAM. Use scsiformat.x as described in this chapter and then use switch.x to set your SCSI ID to 0 | ||
You should be greated with the following screen: | You should be greated with the following screen: | ||
Line 153: | Line 165: | ||
Eject the master floppy and reboot. If everything went well you will have booted from the hard drive. Congratulations! | Eject the master floppy and reboot. If everything went well you will have booted from the hard drive. Congratulations! | ||
- | **Note for SCSI users: You don't need the SxSI drivers and installation of bootloader to SRAM. Use scsiformat.x as described earlier | + | The MasterDiskV2 features a small file commander called |
- | **One last note:** The MasterDiskV2 features a small file commander called **File Professer v1.0** (C)1989 Logos System which is entirely controllable by keyboard. Type fp.x to launch File Professer | + | **Warning:** X68000 allows using long file names, however you will need the [[http:// |
Don't be shy to restore my custom hard disk image with WinImage to your HDD, CF or SD card and use it on your lovely X68000. | Don't be shy to restore my custom hard disk image with WinImage to your HDD, CF or SD card and use it on your lovely X68000. |
x68000/hard_drive_on_sasi_machine.txt · Last modified: 2023/07/04 17:44 by TD-Linux