x68000:writing_floppies
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:writing_floppies [2014/08/07 16:07] – eidis | x68000:writing_floppies [2015/04/04 07:06] – [Windows] segasonicfan | ||
---|---|---|---|
Line 2: | Line 2: | ||
* All floppy disk images, which you want to transfer, must be in XDF format. | * All floppy disk images, which you want to transfer, must be in XDF format. | ||
- | * You can use [[http:// | + | |
- | * Clean the drive heads with isopropyl alcohol if the status of the drive is unknown. Some users reported that their 5.25" floppy drives | + | |
- | * You can get detailed info about various floppy drives and their jumper settings in the FTP's [[http:// | + | * With [[http:// |
+ | * Clean the drive heads with isopropyl alcohol if the status of the drive is unknown. Some users reported that their 5.25" floppy drives | ||
+ | * You can get detailed info about various floppy drives and their jumper settings in the FTP's [[http:// | ||
Line 13: | Line 15: | ||
* [[http:// | * [[http:// | ||
- | OmniFlop requires a built-in NEC-compatible floppy disk controller. You can use the Diagnostic options of OmniFlop to see if this holds for your system. | + | OmniFlop requires a built-in |
**Omniflop Install& | **Omniflop Install& | ||
- | - Install | + | - Install OmniFlop & OmniFDC |
- | - Once Drivers are installed open the omniflop program, go to Next | + | - Once Drivers are installed open the omniflop program |
- | - To format 5.25" select | + | - Select |
- | - Next windows show a list of compatible formats, you can select: | + | - The next windows |
- | * 78/2/8x 1024 Sharp X68000 78-Track 1248Kb | + | * 78/2/8x 1024 Sharp X68000 78-Track 1248Kb |
- | - The format | + | * 77/2/8x 1024 Sharp X68000 77-Track 1232Kb |
+ | - The formatting | ||
**Omniflop Write X68000 Disks:** | **Omniflop Write X68000 Disks:** | ||
- | - Into Omniflop click in Write Disk | + | - Open Omniflop |
- | - Select Drive Unit and maintain selected | + | - Select Drive Unit and make sure that Autodetect format |
- | - In next window you can read: Select a format to write...ALL, | + | - In next window you can read: Select a format to write...ALL, |
- | - In file: you can select only .XDF files*NOTE*, below leave Standard disk image(*img) | + | - In file: you can select only .XDF files (You have to select "show all files" from bottom right window) |
- | - Click next and begin to Write .XDF disk image into Real 5.25" disk | + | - Click next and it will begin to Write .XDF disk image to 5.25" |
- | - After write process | + | - After write process |
* The file is smaller than the disk - not all of the disk has been writen. | * The file is smaller than the disk - not all of the disk has been writen. | ||
* Apart from this, the operation completed OK | * Apart from this, the operation completed OK | ||
- | * Probably | + | - You can ignore this message and press close. |
+ | - Alternatively, | ||
+ | **Using Virtual Floppy Image Converter: | ||
+ | *[[http:// | ||
+ | Many image files you will find online are not .XDF format but in fact .DIM files. | ||
+ | | ||
+ | * The install is straightforward, | ||
+ | right into the window to convert them. Note: If you need to change the language, read the " | ||
+ | install folder for using command prompt to do this. This is only necessary if you select the wrong language on first | ||
+ | start up because reinstalling the program does not change the language. | ||
+ | |||
===== Mac ===== | ===== Mac ===== | ||
x68000/writing_floppies.txt · Last modified: 2022/04/25 16:33 by TD-Linux