x68000:xsimm10_-_memory_expansion_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
x68000:xsimm10_-_memory_expansion_board [2012/01/10 09:51] – eidis | x68000:xsimm10_-_memory_expansion_board [2012/01/23 08:19] – eidis | ||
---|---|---|---|
Line 6: | Line 6: | ||
XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots. | XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots. | ||
- | + | ||
|{{: | |{{: | ||
| XSIMM10 | | XSIMM10 | ||
- | **Selection and implementation of the SIMM module** | + | **Compatible |
- | This XSIMM (Single In-line Memory Module) | + | The XSIMM10 |
*PC/AT: 9-bit (with parity) 30-pin | *PC/AT: 9-bit (with parity) 30-pin | ||
*Macintosh: 8-bit, 30-pin | *Macintosh: 8-bit, 30-pin | ||
- | However, due to the size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions: | + | However, due to the vertical |
*When mounted in slot 1: Less than 15.3mm | *When mounted in slot 1: Less than 15.3mm | ||
Line 24: | Line 24: | ||
If the size is exceeded, the adjacent slot is unusable. | If the size is exceeded, the adjacent slot is unusable. | ||
- | In addition, when used with the following models, you must have a total of 2MB internal memory to add more RAM and 1MB of internal memory expansion board in advance. | + | In addition, when used with the following models, you must have a 1MB of internal memory expansion board in advance and a total of 2MB internal memory to add more RAM. |
{{: | {{: | ||
- | XSIMM10 SIMM modules must have the same access time and memory capacity | + | XSIMM10 SIMM modules must have the same access time and memory capacity |
- | SIMM modules with 4MB or 1MB capacity can be used as a pair. However, to implement two pairs, do not use 4MB SIMM modules. | + | SIMM modules with 4MB or 1MB capacity can be used for the first pair. However, do not use 4MB SIMM modules |
*A Pair (Aペア): | *A Pair (Aペア): | ||
*B Pair (Bペア): Each SIMM module can be only 1MB | *B Pair (Bペア): Each SIMM module can be only 1MB | ||
- | {{: | + | **Dipswitch settings** |
- | **DIP switch settings** | + | Click on the following images to enlarge. |
- | + | ||
- | S1 and S2 DIP switch settings as pictured above. | + | |
- | *0 = ON | + | |{{: |
- | | + | | |
- | (OFF = 1 have been displayed on the board) | + | **Configuration examples** |
- | DIP switch settings as shown below. | + | |
- | |{{:x68000:xsimm10_5.jpg?250|}} |{{:x68000:xsimm10_6.jpg?250|}} | + | |{{:x68000:xsimm10_6_translated.png?350|}} |{{:x68000:xsimm10_7_translated.png?350|}} | |
- | DIP switch | + | Dipswitch |
- | * The product' | + | Keep the scene alive ! |
+ | Eidis |
x68000/xsimm10_-_memory_expansion_board.txt · Last modified: 2019/08/27 20:45 by 127.0.0.1