arcade:joystick_mechs
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
arcade:joystick_mechs [2023/11/22 21:43] – created NFG | arcade:joystick_mechs [2024/06/21 00:10] (current) – NFG | ||
---|---|---|---|
Line 2: | Line 2: | ||
Just a fun-filled list of joystick mounts for easy fact finding. | Just a fun-filled list of joystick mounts for easy fact finding. | ||
- | ==== Seimitsu | + | ===== Pinouts ===== |
- | Seimitsu sticks to two mounting patterns, for the most part. | + | Most of the joysticks listed below use either spade connectors (AT-187 Japan size) or a 5-pin JST NH-series connector. |
- | They' | + | I've attempted to put together a guide to wrapping your head around [[Joystick Wiring]]. |
+ | |||
+ | ===== Seimitsu ===== | ||
+ | Seimitsu sticks to two mounting patterns, for the most part. Either a 50mm square, or 40mm spacing. | ||
+ | |||
+ | Wiring is done with spade connectors (called fast-on connectors in Japan) or a 5-pin connector. | ||
+ | |||
+ | They' | ||
Generally speaking all their adaptor plates are compatible with the stick mechs, so if you have a 40mm stick, any of their **P=40** plates will work. | Generally speaking all their adaptor plates are compatible with the stick mechs, so if you have a 40mm stick, any of their **P=40** plates will work. | ||
Line 11: | Line 18: | ||
Their entire catalogue of available plates (in 2023) is available on the [[arcade: | Their entire catalogue of available plates (in 2023) is available on the [[arcade: | ||
- | === Seimitsu 40mm Mechs === | + | ==== Seimitsu 40mm Mechs ==== |
Most of Seimitsu' | Most of Seimitsu' | ||
+ | |||
+ | {{ : | ||
* SELS-70X | * SELS-70X | ||
Line 20: | Line 29: | ||
* LS-56 | * LS-56 | ||
* LS-55 | * LS-55 | ||
+ | * LS-33 | ||
- | === Seimitsu 50mm Mechs === | + | ==== Seimitsu 50mm Mechs ==== |
* LS-32 | * LS-32 | ||
Line 27: | Line 37: | ||
* NOBI | * NOBI | ||
- | ==== SNK ==== | + | ===== SNK / Sigma / ASCII / Seimitsu ===== |
- | SNK's home consoles used Seimitsu mechs (or clones of them) with a 40mm pattern. | + | SNK' |
+ | |||
+ | These same mechs (or clones of them) were also used in sticks from Sigma (The Σ-2200 definitely used a Seimitsu mech) and some early ASCII models, like the ones made for MSX computers, and the Nintendo Famicom. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Here are some mounting measurements for this device: | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | ===== Sanwa ===== | ||
+ | Sanwa' | ||
+ | |||
+ | {{ : | ||
+ | |||
+ | The two 65mm holes in both the JLX and JLF are not threaded, and typically use a nut & bolt attachment. | ||
+ | |||
+ | The JLF 4-hole mounts are plastic and use self-tapping counter-sink screws to fix the mech to the plate. The JLX sticks however use threaded metal inserts, and so must use different screws than the JLF mechs. | ||
+ | |||
+ | Sanwa sticks are mounted deeper into the panel compared to Seimitsu sticks. | ||
+ | |||
+ | Sanwa sticks use a raised central circle around the pivot, to allow for the pivot to rise vertically above the nominal surface of the stick. | ||
+ | ===== Hori ===== | ||
+ | Hori's made many mechs throughout their history. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The Hayabusa shown above includes the mounting plate. | ||
+ | |||
+ | [[Hori Hayabusa|Hori Hayabusa Info Page]] | ||
+ | |||
+ | ===== ASCII ===== | ||
+ | ASCII made many joysticks, and distributed Sega's Dreamcast arcade stick in North America (as Agetech). | ||
+ | |||
+ | === CX4J === | ||
+ | ASCII were first to market with an optical mechanism, it is branded ASCII (and OMRON) with a part number C4XJ. It was used in several Playstation and Dreamcast sticks, like the [[controls: | ||
+ | |||
+ | It was possibly developed with Sanwa, who later released a nearly identical unit called the **JLHS-8 FLASH 1**. It uses two groups of soldered-on wires, 4-wires for the directional outputs, and two wires for Vcc and Ground, to power the LEDs. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | This mech is compatible with Sanwa JLF mounts and accessories. | ||
+ | |||
+ | ===== Nintendo ===== | ||
+ | Back in the 80s, with Donkey Kong and Popeye, the Vs cabinets, and even R-Type (which Nintendo distributed in North America) Nintendo used an all-metal joystick that was small, clicky, had an incredibly short throw, and a very short shaft. | ||
- | {{: | + | The following diagrams were made based on manual measurements, |
- | ==== Sanwa ==== | + | {{: |
- | Sanwa uses two mount patterns: either a simple 65mm two-screw attachment, or a square pattern that's much smaller than Seimitsu' | + | {{:arcade: |
+ | {{: | ||
+ | {{: | ||
arcade/joystick_mechs.1700653386.txt.gz · Last modified: 2023/11/22 21:43 by NFG