arcade:namco_cyber_lead_pinouts
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
arcade:namco_cyber_lead_pinouts [2024/06/13 12:01] – [Namco Cyber Lead] NFG | arcade:namco_cyber_lead_pinouts [2024/07/06 14:52] (current) – revised the tables NFG | ||
---|---|---|---|
Line 4: | Line 4: | ||
For the most part, all the connectors in the cabinet are one of two types, both made by AMP. The data communications are mostly EI series, and almost everything else is Universal Mate n Lock. Except the connectors on the power supply board, where there are two Molex Mini-Fit Jr. | For the most part, all the connectors in the cabinet are one of two types, both made by AMP. The data communications are mostly EI series, and almost everything else is Universal Mate n Lock. Except the connectors on the power supply board, where there are two Molex Mini-Fit Jr. | ||
- | === EI Series === | ||
+ | ^ <color # | ||
| | | | ||
^ 12-pin Housing | 1-171822-2 | ^ 12-pin Housing | 1-171822-2 | ||
Line 13: | Line 13: | ||
^ Receptacle Contact (26-20 AWG) | 170262-1 | ^ Receptacle Contact (26-20 AWG) | 170262-1 | ||
^ Receptacle Contact (30-26 AWG) | 170205-1 | ^ Receptacle Contact (30-26 AWG) | 170205-1 | ||
- | | Namco recommends | + | ^ <color # |
+ | | ^ Part No. ^ | ||
+ | ^ 6 Pin Housing | 0039013065 | ||
+ | ^ 8 Pin Housing | 0039039082 | ||
+ | ^ Socket Contact | 39000038 | ||
+ | ^ <color # | ||
+ | | ^ Part No. ^ | ||
+ | ^ 15 Pin Plug | 172171-1 | ||
+ | ^ 15 Pin Cap | 172163-1 | ||
+ | ^ 22-18 AWG __Socket__ Contact | 770988-1 | ||
+ | ^ 22-18 AWG __Plug__ Contact | 770987-1 | ||
+ | | Namco recommends | ||
+ | |||
+ | **Note:** The Mini-Universal Mate-N-Lock connector can use either plug or socket connectors in both plug and cap housings. | ||
+ | |||
+ | |||
+ | ---- | ||
===== JVS CONV PCB ===== | ===== JVS CONV PCB ===== | ||
Line 21: | Line 37: | ||
It's called the N48 Harness according to Namco docs, so this is the N48 Harness Connector. | It's called the N48 Harness according to Namco docs, so this is the N48 Harness Connector. | ||
+ | ^ <color # | ||
| {{: | | {{: | ||
^ Pin ^ Function | ^ Pin ^ Function | ||
Line 28: | Line 45: | ||
| 4 | P1 Button 4 | 9 | P2 Button 6 | | | 4 | P1 Button 4 | 9 | P2 Button 6 | | ||
| 5 | P2 Button 4 | 10 | GND | | | 5 | P2 Button 4 | 10 | GND | | ||
+ | |||
+ | |||
+ | ---- | ||
===== I/O & LED Board ===== | ===== I/O & LED Board ===== | ||
Line 33: | Line 53: | ||
==== Player Controls ==== | ==== Player Controls ==== | ||
- | Pretty standard stuff here. Labeled J33 (P1) and J35, these are EI-series 12-pin connectors, used to connect all the signals from the control panel to the PCB. The pinout is the same for P1 and P2. The manual indicates a red connector is used for player 2. | + | Pretty standard stuff here. Labeled |
+ | ^ <color # | ||
| {{: | | {{: | ||
^ Pin ^ Function | ^ Pin ^ Function | ||
Line 43: | Line 64: | ||
| 5 | Start | 11 | Button 6 | | | 5 | Start | 11 | Button 6 | | ||
| 6 | Button 1 | 12 | GND | | | 6 | Button 1 | 12 | GND | | ||
+ | |||
==== Coin Control ==== | ==== Coin Control ==== | ||
Labeled J38 on the board, this connector is wired to the coin input and counter. | Labeled J38 on the board, this connector is wired to the coin input and counter. | ||
+ | ^ <color # | ||
| {{: | | {{: | ||
^ Pin ^ Function | ^ Pin ^ Function | ||
Line 52: | Line 75: | ||
| 2 | Coin 1 | 5 | Counter 2 | | | 2 | Coin 1 | 5 | Counter 2 | | ||
| 3 | Coin 2 | 6 | Service | | | 3 | Coin 2 | 6 | Service | | ||
+ | |||
==== Power ==== | ==== Power ==== | ||
+5V is available from J31, using a 2-pin connector. | +5V is available from J31, using a 2-pin connector. | ||
+ | ^ <color # | ||
| {{: | | {{: | ||
^ Pin ^ Function | ^ Pin ^ Function | ||
Line 66: | Line 91: | ||
The connection to the LED panel itself, from the LED board beneath it, uses the same 10-pin connector as the N48 harness. | The connection to the LED panel itself, from the LED board beneath it, uses the same 10-pin connector as the N48 harness. | ||
+ | ^ <color # | ||
| {{: | | {{: | ||
^ Pin ^ Function | ^ Pin ^ Function | ||
Line 78: | Line 104: | ||
It's a straight through configuration, | It's a straight through configuration, | ||
+ | |||
+ | ---- | ||
===== Joystick ===== | ===== Joystick ===== | ||
Line 102: | Line 130: | ||
^ Contact (28-22 AWG) | SHF-001T-0.8BS | ^ Contact (28-22 AWG) | SHF-001T-0.8BS | ||
^ Contact (30-28 AWG) | SHF-002T-0.8BS | ^ Contact (30-28 AWG) | SHF-002T-0.8BS | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ===== Power Supply ==== | ||
+ | There are two output connectors on the PSU, which are 8 and 6 pin Molex New Mini-Fit Jr connectors. | ||
+ | |||
+ | ^ <color # | ||
+ | | {{ : | ||
+ | ^ Pin ^ Function | ||
+ | | 1 | 2.5V | 2 | 3.3V | 3 | 5V | | ||
+ | | 4 | GND | 5 | GND | 6 | GND | | ||
+ | |||
+ | |||
+ | ^ <color # | ||
+ | | {{ : | ||
+ | ^ Pin ^ Function | ||
+ | | 1 | 2.5V | 2 | 3.3V | 3 | 5V | 4 | 12V | | ||
+ | | 6 | GND | 7 | GND | 7 | GND | 8 | GND | | ||
+ | |||
+ | | ||
+ | |||
+ | ===== Power ===== | ||
+ | This plug connects the power cables from the PSU to the rest of the cabinet. | ||
+ | |||
+ | ^ <color # | ||
+ | | {{ : | ||
+ | ^ Pin ^ Function | ||
+ | | 1 | 12V | 2 | 12V | 3 | GND | 4 | GND | 5 | GND | | ||
+ | | 6 | 3.3V | 7 | 3.3V | 8 | GND | 9 | GND | 10 | GND | | ||
+ | | 11 | 5V | 12 | 5V | 13 | 5V | 14 | GND | 15 | GND | | ||
+ |
arcade/namco_cyber_lead_pinouts.1718244077.txt.gz · Last modified: 2024/06/13 12:01 by NFG