Differences

This shows you the differences between two versions of the page.

--- x68000:cz-6bm1a_-_midi_board [2014/08/09 19:56] – eidis
+++ x68000:cz-6bm1a_-_midi_board [2019/08/27 20:45] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ====== CZ-6BM1A ======
+All info taken from http://www.geocities.co.jp/SiliconValley3115/info/data/cz6bm1a.html
 |{{:x68000:cz-6bm1a_1.jpg?250|}}  |{{:x68000:cz-6bm1a_2.jpg?250|}}  |{{:x68000:cz-6bm1a_3.jpg?250|}}  |
+CZ-6BM1A is a genuine SHARP MIDI board which meets the VCCI (electromagnetic interference) standards. Apart from that it is functionally the same as its predecessor CZ-6BM1.
 ====== Hardware specifications ======
@@ Line 7: / Line 11: @@
 |Control LSI  |YM3802（MCS）  |
 |Interrupt  |Level 2 / Level 4 (Set by SW1)  |
-|DATA terminal  |DATA OUT 2, DATA OUT 1 (It is possible to switch one port to DATA THRU)  |
+|DATA terminal  |DATA OUT 1, DATA OUT 2 (It is possible to switch one port to DATA THRU)  |
 |Tape sync signal  |FSK 1200bps, Tape sync input terminal 1, Tape sync output terminal 1  |
 |Power consumption  |+5V 180mA  |
 |External dimensions  |150mm width x 140mm depth x 18mm height  |
 |Weight  |About 150g  |
-|Accessories  |I / O slot cover (2 types), Fixing screw (1 pcs.), Instructions (1 books), Warranty (Part 1), Customer consultation List (Part 1), Dedicated MIDI conversion cable (3 pcs.)  |
+|Accessories  |I/O slot cover (2 types), Fixing screw, Instruction manual, Warranty, Customer consultation List, Dedicated MIDI conversion cable (3 pcs.)  |
 ====== Part descriptions ======
@@ Line 18: / Line 22: @@
 ====== Dip-switch settings ======
+{{:x68000:cz-6bm1a_5.png?50|}}
+DATA OUT / THRU and interrupt level DIP switch settings
-|DATA OUT / THRU and interrupt level DIP switch settings  |Port address jumper settings  |
+| |SW1  |  Function  |
+|1  |  ON  |Interrupt level 4  |
-| |SW1  |Function  |
+| |  OFF  |Interrupt level 2  |
-|1  |ON  |Interrupt level 4  |
+|2  |  ON  |DATA　OUT  |
-| |OFF  |Interrupt level 2  |
+| |  OFF  |DATA　THRU  |
-|2  |ON  |DATA　OUT  |
-| |OFF  |DATA　THRU  |
   *Default is 1 and 2 ON
-|JP1  |Port address  |
-|1  |＄EAFA01～＄EAFA0F  |
+{{:x68000:cz-6bm1a_4.png?50|}}
-|2  |＄EAFA11～＄EAFA1F  |
+Port address jumper settings
+|  JP1  |  Port address  |
+|  1  |＄EAFA01～＄EAFA0F  |
+|  2  |＄EAFA11～＄EAFA1F  |
   *Default is 1