x68000:hard_drive_on_sasi_machine
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
x68000:hard_drive_on_sasi_machine [2014/06/04 07:30] – [Chapter 4: SASI strikes back] eidis | x68000:hard_drive_on_sasi_machine [2023/07/04 17:44] (current) – add another link TD-Linux | ||
---|---|---|---|
Line 2: | Line 2: | ||
Using a SCSI to IDE/CF/SD adaptor as a hard drive on X68000 hardware. | Using a SCSI to IDE/CF/SD adaptor as a hard drive on X68000 hardware. | ||
- | Six devices are detailed below: | + | Seven devices are detailed below: |
- | * I-O Data IDSC21-E | + | * I-O Data [[http:// |
- | * Yamaha V769970 | + | * Yamaha |
- | * Acard AEC-7720U | + | * Acard [[http:// |
- | * I-O Data R-IDSC-E/ | + | * I-O Data [[http:// |
- | * STRATOS CF AztecMonster | + | * STRATOS |
- | * code/src designs SCSI2SD | + | * code/src designs |
+ | * Classic PC Rescue Committee [[http:// | ||
Most of them were tested on an ACE-HD system, but compatibility for all X68000 should be the same. | Most of them were tested on an ACE-HD system, but compatibility for all X68000 should be the same. | ||
Line 52: | Line 53: | ||
{{: | {{: | ||
- | **SCSI2SD** is an open hardware and open source project by [[http:// | + | **SCSI2SD** is an open hardware and open source project by [[http:// |
+ | |||
+ | For **SCSI2SD** the following settings were used: | ||
+ | * SCSI ID3 | ||
+ | * Termination On | ||
+ | * Parity Off | ||
+ | |||
+ | To support the HDD LED, see [[x68000: | ||
{{: | {{: | ||
+ | |||
+ | **CLPC-CFSxSI101** is special because it is the only one which can be used in native SASI or SCSI mode. All previous adapters only work in SCSI mode. It is made in Japan, works with CF cards and can be purchased from [[http:// | ||
+ | |||
+ | {{: | ||
==== Chapter 2 Connecting the hardware ==== | ==== Chapter 2 Connecting the hardware ==== | ||
Line 77: | Line 89: | ||
{{x68000: | {{x68000: | ||
- | Please follow | + | Please follow |
+ | |||
+ | [[x68000: | ||
[[http:// | [[http:// | ||
Line 85: | Line 99: | ||
First of all download the disk image which contains Human 68k v3.02 and SCSI compatible IOCS driver with DMA patch for X68000 machines with SASI port. The DMA patch was discovered by our forum member Neko68k and is reproduced with his kind permission. | First of all download the disk image which contains Human 68k v3.02 and SCSI compatible IOCS driver with DMA patch for X68000 machines with SASI port. The DMA patch was discovered by our forum member Neko68k and is reproduced with his kind permission. | ||
- | * [[http:// | + | * [[http:// |
Download DiskExplorer and the disk image transfer tool for your operating system. | Download DiskExplorer and the disk image transfer tool for your operating system. | ||
- | * [[http:// | + | * [[http:// |
* [[http:// | * [[http:// | ||
* [[http:// | * [[http:// | ||
Line 97: | Line 111: | ||
==== Chapter 4: SASI strikes back ==== | ==== Chapter 4: SASI strikes back ==== | ||
+ | |||
+ | **Note for SCSI users:** SUPER, XVI, XVI Compact, X68030, X68030 Compact do not need the SxSI driver and installation of bootloader to SRAM. Use scsiformat.x as described in this chapter and then use switch.x to set your SCSI ID to 0 | ||
You should be greated with the following screen: | You should be greated with the following screen: | ||
Line 126: | Line 142: | ||
* Initialize device ? (Y/N) | * Initialize device ? (Y/N) | ||
* Format disk ? (Y/N) | * Format disk ? (Y/N) | ||
- | - Reinitialize device (Do not use or it will mess up the disk and make it unbootable) | + | - Reinitialize device (Do not use or it will make the disk unbootable) |
- Change device | - Change device | ||
* Enter device ID (0~7) | * Enter device ID (0~7) | ||
Line 140: | Line 156: | ||
</ | </ | ||
- | It will install a bootloader in SRAM which will be executed on every reboot. | + | It will install a bootloader in SRAM which will be executed on every reboot. |
+ | |||
+ | * HELP to call the boot menu and boot from another partition | ||
+ | * OPT.1 to force booting from floppy | ||
{{x68000: | {{x68000: | ||
Line 150: | Line 169: | ||
Eject the master floppy and reboot. If everything went well you will have booted from the hard drive. Congratulations! | Eject the master floppy and reboot. If everything went well you will have booted from the hard drive. Congratulations! | ||
- | **Note for SCSI users: You don't need the SxSI drivers and installation of bootloader to SRAM. Use scsiformat.x as described earlier | + | The MasterDiskV2 features a small file commander called |
- | **One last note:** The MasterDiskV2 features a small file commander called **File Professer v1.0** (C)1989 Logos System which is entirely controllable by keyboard. Type fp.x to launch File Professer | + | **Warning:** X68000 allows using long file names, however you will need the [[http:// |
Don't be shy to restore my custom hard disk image with WinImage to your HDD, CF or SD card and use it on your lovely X68000. | Don't be shy to restore my custom hard disk image with WinImage to your HDD, CF or SD card and use it on your lovely X68000. |
x68000/hard_drive_on_sasi_machine.1401831010.txt.gz · Last modified: 2019/08/27 20:44 (external edit)