x68000:internet_on_x68000_using_ethernet_or_null_modem_cable
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
x68000:internet_on_x68000_using_ethernet_or_null_modem_cable [2019/01/26 07:43] – [Ethernet Instructions] neko68k | x68000:internet_on_x68000_using_ethernet_or_null_modem_cable [2019/08/27 20:45] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 3: | Line 3: | ||
This article is a kind contribution by our forum member **Neko68k**. Thank you for shedding light on this rather grey area ! | This article is a kind contribution by our forum member **Neko68k**. Thank you for shedding light on this rather grey area ! | ||
- | This article will cover configuring your X68000 for internet access using either a null-modem cable or an ethernet card. Neptune-X | + | This article will cover configuring your X68000 for internet access using either a null-modem cable or an ethernet card. Neptune-X, Nereid, and RaSCSI |
==== Downloads ==== | ==== Downloads ==== | ||
Line 13: | Line 13: | ||
=== For Ethernet === | === For Ethernet === | ||
|[[http:// | |[[http:// | ||
+ | |||
+ | === For Emulated Ethernet === | ||
+ | |[[http:// | ||
=== For Serial === | === For Serial === | ||
Line 66: | Line 69: | ||
[[http:// | [[http:// | ||
- | I followed the steps [[https:// | + | I followed the steps [[https:// |
*On your x68k run PPPX.BAT. | *On your x68k run PPPX.BAT. | ||
Line 79: | Line 82: | ||
Thanks to GIMONS for pointing me in the right direction. | Thanks to GIMONS for pointing me in the right direction. | ||
- | XM6G Specifics: | + | === General === |
- | *Use OpenVPN TAP driver. | + | |
- | | + | Add your ethernet |
- | | + | |
- | *In XM6G put your TAP interface name in the Nererid tab. | + | |
- | | + | |
I recommend creating a BAT file with the following commands: | I recommend creating a BAT file with the following commands: | ||
Line 90: | Line 90: | ||
xip -t -1 | xip -t -1 | ||
ifconfig lp0 up | ifconfig lp0 up | ||
- | ifconfig en0 192.168.0.11 | + | ifconfig en0 x68k netmask 255.255.255.0 up |
- | inetdconf +dns 192.168.0.1 +domain x68k +router 192.168.0.1 | + | inetdconf +dns 8.8.8.8 +domain x68k +router 192.168.0.1 |
</ | </ | ||
- | Run your BAT file. | + | In the above snippet ' |
+ | |||
+ | Run your BAT file and test with ' | ||
+ | |||
+ | === XM6G Specifics === | ||
+ | *Use OpenVPN TAP driver. | ||
+ | | ||
+ | *You _must_ set a static IP to the TAP device before bridging. This IP should be in your local subnet and will be the IP address for the x68k. It should be specified in /etc/hosts as described above. (ex. 10.0.0.x, 162.168.0.x). The default router should be _your_ router (ex. 10.0.0.1, 192.168.0.1). | ||
+ | | ||
+ | *In XM6G put your TAP interface name in the Nereid tab. | ||
+ | | ||
+ | *Now follow the General instructions above if you haven' | ||
+ | |||
x68000/internet_on_x68000_using_ethernet_or_null_modem_cable.1548452587.txt.gz · Last modified: 2019/08/27 20:44 (external edit)