x68000:xellent30s_-_cpu_accelerator_board
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
x68000:xellent30s_-_cpu_accelerator_board [2014/08/26 01:45] – eidis | x68000:xellent30s_-_cpu_accelerator_board [2019/08/27 20:45] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 16: | Line 16: | ||
**Package contents** | **Package contents** | ||
- | Everything | + | Everything |
*Xellent30s board | *Xellent30s board | ||
Line 28: | Line 28: | ||
**DIP switch settings** | **DIP switch settings** | ||
- | *Select the Xellent30s I/O port address by using DIP switch. | + | *Select the Xellent30s I/O port address by using DIP switches. |
- | *Default DIP switch settings | + | *Default DIP switch settings |
- | *Set upper yellow | + | *Set DIP switches to ON or OFF. ON - UP, OFF - DOWN |
*Address space from $EC0000 to $ECFFFF can be used. Please select address that you are not using. | *Address space from $EC0000 to $ECFFFF can be used. Please select address that you are not using. | ||
*Factory default settings are $ECC000 to $ECFFFF (See Figure 1) | *Factory default settings are $ECC000 to $ECFFFF (See Figure 1) | ||
{{: | {{: | ||
+ | |||
+ | The DIP switch settings were taken from Xellent30s manual by Tokyo Systems Research Co. Ltd. | ||
**Hardware installation** | **Hardware installation** | ||
Line 44: | Line 46: | ||
**Testing the Xellent30s** | **Testing the Xellent30s** | ||
- | When you have finished installing | + | After the installation, |
- | Analog RGB, with minimal configuration of the keyboard, turn on the unit after it was confirmed | + | |
- | Body does not start, | + | |
- | After confirming that the body starts | + | **Installing the CPU boot selection menu** |
- | Run. | + | |
- | " | + | By default the Xellent30s will start in 68000 mode when the X68000 is switched on and you will need a driver to use it in MC68030 mode. A program |
- | Then, please | + | |
+ | The CPU boot selection menu can be installed in SRAM by using the following procedure. | ||
+ | *1) ch30inst.x and ch30.sys must be in the current directory. | ||
+ | | ||
+ | *ch30inst.x - installer of ch30.sys | ||
+ | *2) Type ch30inst and [Enter]. This will install ch30.sys to SRAM. If will not install if SRAM does not have enought free space. In that case, please | ||
+ | *3) The CPU boot selection menu is now installed to SRAM. You can use the numeric keys or cursor keys to select the CPU which you wish to boot. | ||
+ | |||
+ | **3rd party drivers** | ||
+ | |||
+ | *[[http:// | ||
+ | *[[http:// | ||
+ | |||
+ | **Installing the SRAM driver without ch30inst.x** | ||
- | **Register MPU boot selection menu** | + | |
+ | | ||
+ | | ||
+ | | ||
- | Initially | + | < |
- | The MC68030 is actually to work, you need a software operation. | + | >switch boot=scsi0 - Sets the ROM boot mode and ROM boot address |
- | MC68000, a program to start the user to easily choose either to start MC68030, are included in the setup disk. | + | >db - Starts |
- | Register MPU boot selection menu to SRAM following procedure. | + | -mes e8e00d 31 - Enables writing |
- | (1) provided in the current directory and ch30.sys ch30inst.x. | + | -fs ed0100 ed3fff 00 - Clears |
- | The above installer ch30inst.x • • • Select | + | -rch30_omake.sys,ed0100 - Copies ch30_omake.sys to SRAM |
- | There is insufficient free space of the SRAM can not be registered. | + | -mew ed0100+[ed0106].l 4e75 - Sets the length of the SRAM boot program |
- | If so, please delete | + | -mel ed0106 [ed000c].l - Sets the ROM boot address |
- | (3) In this "boot selection menu MPU" I reside in the SRAM. | + | -mes ed0106 |
- | Cursor keys, numeric keys, or you can choose you want to start the MPU. | + | -mel ed010a ecc000 - Sets the I/O port address of Xellent30 |
+ | -mes e8e00d 00 - Finishes writing to SRAM | ||
+ | -q - Exits the debugger | ||
+ | >switch sram=program - Sets the SRAM usage mode | ||
+ | > | ||
+ | </ | ||
- | DIP switch settings, etc., was taken from the instruction manual Xellent30s Systems Research Inc., Tokyo. | + | **Boot keys after installation** |
- | * The product' | + | |
+ | *[XF3] .... Switch MPU. | ||
+ | *[SPACE] ... Same as above. | ||
+ | *[XF4] .... Temporarily turn off the MPU cache of 68030. | ||
+ | *[XF5] .... Display SCSI boot ID (+ extra options) selection menu. | ||
+ | *[ESC] .... Temporarily boots as STD. | ||
+ | *[HELP] .... Boots with HD Start Partition Selection Menu (IPL MENU). | ||
x68000/xellent30s_-_cpu_accelerator_board.1408981514.txt.gz · Last modified: 2019/08/27 20:44 (external edit)