Differences

This shows you the differences between two versions of the page.

--- x68000:xsimm10_-_memory_expansion_board [2012/01/10 09:51] – eidis
+++ x68000:xsimm10_-_memory_expansion_board [2012/01/23 08:33] – eidis
@@ Line 6: / Line 6: @@
 XSIMM10 (Ten X-Sim) was manufactured and sold from 1994 by Systems Research Ltd., Tokyo. It is a memory expansion board for the X68000 series. This product uses commercially available SIMM modules (not included) mounted on board, and is compatible with X68000 I/O expansion slots.
 |{{:x68000:xsimm10_2.jpg|}}  |
 |  XSIMM10  |
-**Selection and implementation of the SIMM module**
+**Compatible SIMM modules**
-This XSIMM (Single In-line Memory Module) board can be used with the following commercially available SIMM modules for compatible machines:
+The XSIMM10 board can be used with the following commercially available SIMM modules:
   *PC/AT: 9-bit (with parity) 30-pin
   *Macintosh: 8-bit, 30-pin
-However, due to the size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions:
+However, due to the vertical size limitations of I/O expansion slots, there are following SIMM module vertical size restrictions:
-  *When mounted in slot 1: Less than 15.3mm
+  *When mounted in slot 1: Height must be less than 15.3mm
-  *When mounted in slot 2: Less than 20.4mm
+  *When mounted in slot 2: Height must be less than 20.4mm
 If the size is exceeded, the adjacent slot is unusable.
-In addition, when used with the following models, you must have a total of 2MB internal memory to add more RAM and 1MB of internal memory expansion board in advance.
+In addition, when used with the following models, you must have a 1MB of internal memory expansion board in advance and a total of 2MB internal memory to add more RAM.
 {{:x68000:xsimm10_3_translated.png?300|}}
-XSIMM10 SIMM modules must have the same access time and memory capacity as a pair or two pairs. The RAM can be expanded up to 10MB maximum.
+XSIMM10 SIMM modules must have the same access time and memory capacity for each pair. The RAM can be expanded up to 10MB maximum.
-SIMM modules with 4MB or 1MB capacity can be used as a pair. However, to implement two pairs, do not use 4MB SIMM modules.
+SIMM modules with 4MB or 1MB capacity can be used for the first pair. However, do not use 4MB SIMM modules for the second pair.
-  *A Pair (Ａペア): Each SIMM module can be 4MB or 1MB (You must specify the capacity of installed SIMM modules).
+  *A Pair (Ａペア): Both SIMM modules can be 4MB or 1MB (You must specify the capacity of installed SIMM modules).
-  *B Pair (Bペア): Each SIMM module can be only 1MB
+  *B Pair (Bペア): Both SIMM modules can be only 1MB
-{{:x68000:xsimm10_4.jpg?300|}}
+**Dipswitch settings**
-**DIP switch settings**
+Click on the following images to enlarge.
-S1 and S2 DIP switch settings as pictured above.
-  *0 = ON
+|{{:x68000:xsimm10_4.jpg?350|}}  |{{:x68000:xsimm10_5_translated.png?350|}}  |
-  *1 = OFF
+|  OFF = 1 is displayed on the board  |  S1 and S2 Dipswitch settings as pictured above  |
-(OFF = 1 have been displayed on the board)
+**Configuration examples**
-DIP switch settings as shown below.
-|{{:x68000:xsimm10_5.jpg?250|}}  |{{:x68000:xsimm10_6.jpg?250|}}  |{{:x68000:xsimm10_7.jpg?250|}}  |
+|{{:x68000:xsimm10_6_translated.png?350|}}  |{{:x68000:xsimm10_7_translated.png?350|}}  |
+|  S1 Dipswitch settings  |  S2 Dipswitch settings  |
-DIP switch settings, etc., was taken from the instruction manual XSIMM10 Systems Research Inc., Tokyo.
+Dipswitch settings were taken from XSIMM10 instruction manual, copyright by Systems Research Ltd., Tokyo.
-* The product's manufacturer, Research Systems, Ltd., Tokyo is.
+Keep the scene alive !
+Eidis