psx_overclock
Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
psx_overclock [2006/04/25 11:45] – created 205.188.116.138 | psx_overclock [2019/08/27 20:45] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
===== TITLE ===== | ===== TITLE ===== | ||
- | Intro | + | |
- | The psx cpu runs at about 32MHz by doing this mod you can overclock | + | The Sony PlayStation CPU runs by default at ~33MHz, with this O/C mod you can take the CPU frequency |
+ | |||
+ | |||
==== SECTION ONE ==== | ==== SECTION ONE ==== | ||
- | Start by disassembling your console. We need to get down to JUST the motherboard. I’ll let you get there, its self explanatory. Locate CPU SONY, CDX8606BQ. Turn the board so SONY reads going down, and so does the model number. The fourth (4th) PIN from the left over needs to be lifted, like in the picture below… Simply count from the left, 4… Take your razor blade, and place it under the 4th PIN. Lightly apply pressure where the blade would be pushing on the PIN from the bottom. NOTE: Other nearby PINs will likely move too. Once the CPU PIN is lifted and out of the way, simply adjust the other PINs that moved too. | ||
- | Now, you need to locate your motherboard’s clock chip. This chip sends out a 64 MHz signal that gets divided by the CPU and another processor. I think it’s the graphics processor, RSX? Anyway… This 6 PIN chip is usually labeled “2194A”, | ||
- | To locate | + | |
+ | Welcome to the Playstation overclocking guide! This guide will show you how to increase the overall performance of your Playstation and/or PSOne console. We will be performing this modification on a PSOne console, although the procedure is the same for the chunky Playstations. As with any hardware modification, | ||
+ | |||
+ | |||
+ | |||
+ | **Tools you will need** | ||
+ | |||
+ | *Phillips Screwdriver | ||
+ | *X-acto knife or Jeweler' | ||
+ | *Soldering iron and Solder | ||
+ | *4-pin Crystal oscillator Where do I get one of these? | ||
+ | |||
+ | |||
+ | **About the procedure** | ||
+ | |||
+ | What we are going to be doing is fairly simple: We will be intercepting the 67 MHz clock signal that is sent to the CPU. The CPU internally divides whatever signal | ||
+ | |||
+ | Opening the PSOne (and Playstation) is very simple. Just be careful when removing the CD-ROM assembly, as the data ribbons are very fragile and easy to damage. Once you are looking at the motherboard, | ||
+ | |||
+ | |||
+ | Now lets look at the PLL chip. We will need to carefully disconnect pin 5 on this chip, as this pin sends out the 67 MHz frequency that the CPU runs off of. Now that we have our 67 MHz frequency disconnected, you may want to hook up the Playstation and verify that the CPU is not getting a signal. The Playstation should NOT boot. Once you have verified this, continue on. | ||
+ | |||
+ | Next we need to prepare our oscillator by running a 5V power source and GND to the appropriate pins. A suitable GND for our oscillator is not hard to find, I will usually hook up my ground to a screw that holds down the RF shielding. As for our power source, we will need to pull +5V from the voltage regulator. Now that we have the oscillator properly installed, we need to run our new clock signal on the CPU. This is where it can get tricky, as you will need to raise pin 4 on the Playstation' | ||
+ | |||
+ | Once you have connected the output pin on the oscillator to Pin 4 on the CPU, double check all of your connections. Once you feel everything is installed properly, assemble, hook it up, and test! As always with overclocking, | ||
+ | |||
+ | I hooked mine up and it works great! Since the CPU runs at a modest 40 MHz, you will not need to install any cooling devices. Doing so would be a waste of time and effort. Good luck with your overclocking! | ||
+ | |||
+ | |||
- | You can either solder directly to the IC, or to the solder point (pointed to in blue) on the 7501 console, and maybe other models too. Simply follow the trace in the board and see if it leads to an obvious, and easy solder point. To do this, locate PIN 6 on clock chip, and look for a light green trace going from this PIN, and follow it to an easy solder point. DO NOT go past in-line components like resistors and capacitors! IF you do not find an easy solder point, you’ll have to solder to the IC itself. No biggie, it’s easy! | ||
Line 16: | Line 45: | ||
---- | ---- | ||
- | Credits, external links, etc. | + | This is a modified version of the original article written by Robert Ivy. A tutorial with photos can be seen at www.undergroundcm.com |
+ | |||
+ | All content on this page is (c)2004, 2006 Underground Console Mods. This information can only be shared if credit is given to the respective creator; Robert Ivy |
psx_overclock.1145929514.txt.gz · Last modified: 2019/08/27 20:44 (external edit)