Differences

This shows you the differences between two versions of the page.

--- x68000:040excel_necessary_modifications [2015/06/14 15:53] – hyperneogeo
+++ x68000:040excel_necessary_modifications [2019/08/27 20:45] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ===== 040EXCEL Necessary Modifications =====
-If you're lucky enough to find yourself in possession of an 040EXCEL accelerator board, there are some things you'll need.  First, grab [[gamesx>x68000/Misc/Drivers/040EXCEL%20software/|the 040EXCEL drivers]] from the GameSX X68000 archive.  Then bust out your soldering iron 'cause it's gonna get fun in here.
+If you're lucky enough to find yourself in possession of an 040EXCEL accelerator board, there are some things you'll need.  First, grab [[http://nfggames.com/x68000/Misc/Drivers/040EXCEL%20software/|the 040EXCEL drivers]] from the GameSX X68000 archive　(Thank you Plastic-san!).  Then bust out your soldering iron 'cause it's gonna get fun in here.
 The photos are terrible because 1998, so if you're doing any of these mods, please snap some new ones.
@@ Line 37: / Line 37: @@
 {{ :x68000:kpointr.jpg?100 |}}
-Enclosed in the red frames are 4 ICs: IC4, 5, 11, 12 (all are AS245) and put them in sockets.
+Put the 4 ICs: IC4, 5, 11, 12 (all are AS245) in the red frames into sockets.
 赤枠で囲った４つのＩＣ4、5、11、12（すべてＡＳ２４５）をソケット化します。
@@ Line 59: / Line 59: @@
 {{ :x68000:jumper.jpg?100 |}}
-Next there are 2 AS245s, connect the 19th pin to the reconfiguring cable, and 10th pin to ground. And then make 2 jumper sockets. And make the jumpers like 2-18, 3-17.....9-11... etc.
+Next there are 2 AS245s, connect the 19th pins to the reconfiguring cable, and 10th pin to ground. And then make 2 jumper sockets. And configure the jumpers as 2-18, 3-17.....9-11... etc.
 　次にＡＳ245を二つの、１９ピンに改造用ケーブルの線をつなぐ。もち、１０ピンはＧＮＤ。
@@ Line 66: / Line 66: @@
 {{ :x68000:kaizou.jpg?100 |}}
-IC 4, 5 in the jumper socket, then IC11, 12...then the AS245s are complete. Then take the reconfiguring cable and connect it to the EXCEL, and you are done.
+Put IC 4, 5 in the jumper socket, then the AS245s into IC11, 12 ...and that should do it for the AS245s. Finally take the reconfiguring cable and connect it to the EXCEL, then you are done.
 ＩＣ4，5にジャンパソケット、ＩＣ11，12に改造済みＡＳ245、改造用ケーブルをエクセルにつないで完成。
@@ Line 76: / Line 76: @@
 {{ :x68000:superr.jpg?100 |}}
-Put all the ones marked in a socket. IC59, 72, 73, 74, 85, 86, (6 of em). IC72, 74 are F245s and all the rest are F(ALS)244's. Put them all in the jumper sockets. Do the same with what you did with the XVI regarding the slot.
+Put all the ones marked in the picture into a socket. IC59, 72, 73, 74, 85, 86, (6 of em). IC72, 74 are F245s and all the rest are F(ALS)244's. Put them all in the jumper sockets. Do the same with what you did with the XVI regarding the slot.
 　図の部分をソケット化。ＩＣ59、72、73、74、85、86の６箇所。（ＩＣ72，74はＦ245、それ以外はＦ（ＡＬＳ）244）