| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| x68000:how_to_open_x68000_compact [2014/08/13 02:33] – eidis | x68000:how_to_open_x68000_compact [2019/08/27 20:45] (current) – external edit 127.0.0.1 |
|---|
| ====== How to open X68000 Compact ====== | ====== How to open X68000 Compact ====== |
| |
| |{{:x68000:open_compact_01.jpg?200|}}| Remove the screws on the bottom → only one. | | All info taken from http://x68k-retro.cocolog-nifty.com/blog/2008/04/x68000_compact__11fb.html |
| |{{:x68000:open_compact_02.jpg?200|}}| Remove Slide the bottom part | | |
| |{{:x68000:open_compact_03.jpg?200|}}| Remove the cover of the expansion board → use the driver again Since there is a nail → Remove the panel on the left when viewed from the front, remove the base there. | | |{{:x68000:open_compact_01.jpg?300|}}| Unscrew the screw at the bottom. | |
| |{{:x68000:open_compact_04.jpg?200|}}| I remove the panel on the right side. This ※ Remove the shield on the left to remove it towards the top and from the bottom → Remove the panel in the back, is OK at any timing. | | |{{:x68000:open_compact_02.jpg?300|}}| Slide and remove the bottom part. | |
| |{{:x68000:open_compact_05.jpg?200|}}| To detach twist as photo while pulling it back → | | |{{:x68000:open_compact_03.jpg?300|}}| Remove the expansion board cover. Open the left panel, when viewed from the front. | |
| |{{:x68000:open_compact_06.jpg?200|}}| Remove the panel at the top | | |{{:x68000:open_compact_04.jpg?300|}}| Remove the panel on the right side. Remove the shield on the left. Remove the back panel. It removes from bottom to top. | |
| |{{:x68000:open_compact_07.jpg?200|}}| There are claws of two places in upper and disconnect it on the side of the nail down, is the front panel of the northeast. Please check with a photograph detent position, respectively. | | |{{:x68000:open_compact_05.jpg?300|}}| | |
| |{{:x68000:open_compact_08.jpg?200|}}| | | |{{:x68000:open_compact_06.jpg?300|}}| Remove the panel at the top. Twist it as shown in the photo and pull it back. | |
| |{{:x68000:open_compact_09.jpg?200|}}| | | |{{:x68000:open_compact_07.jpg?300|}}| This is the front panel. Unhook the plastic tabs at the bottom and in two places at the top. Use photos for reference. | |
| |{{:x68000:open_compact_10.jpg?200|}}| It is easy to remove nails left when viewed from the front. Remove the nails so as to lift with a flathead screwdriver → this is located at the position of the button at the top right side of the nail, I pull on the front. Please put a force, making sure that the claws are out to ensure. | | |{{:x68000:open_compact_08.jpg?300|}}| | |
| |{{:x68000:open_compact_11.jpg?200|}}| | |{{:x68000:open_compact_09.jpg?300|}}| | |
| |{{:x68000:open_compact_12.jpg?200|}}| It is a cinch the rest. I remove the white ring of 1. vinyl tape 2. plastic that holds the power cable. | | |{{:x68000:open_compact_10.jpg?300|}}| It is easy to unhook plastic tabs from the front. Unhook the plastic tabs by lifting them with a flathead screwdriver and lift the bezel. | |
| |{{:x68000:open_compact_13.jpg?200|}}| 3.5 inches FDD | | |{{:x68000:open_compact_11.jpg?300|}}| |
| |{{:x68000:open_compact_14.jpg?200|}}| I Remove the flat cable. I remove the cable side of the FDD. Pull over to after removing each receive an equal part of the nail sure that stopped four places in the claws of the plastic. | | |{{:x68000:open_compact_12.jpg?300|}}| The rest is easy. Unhook the white plastic ring and vinyl tape that holds the power cable. | |
| |{{:x68000:open_compact_15.jpg?200|}}| If you do not remove the expansion box ※ carefully, bracket for board expansion ※ breaks the board unchecked? It does not come off that it is not removed from the body all the bracket. Pull over to after removing each receive an equal part of the nail sure that stopped four places in the claws of the plastic. | | |{{:x68000:open_compact_13.jpg?300|}}| Unplug the flat cables from 3.5" FDD drives. | |
| |{{:x68000:open_compact_16.jpg?200|}}| | | |{{:x68000:open_compact_14.jpg?300|}}| Unhook the four plastic tabs and remove the FDD drives. | |
| |{{:x68000:open_compact_17.jpg?200|}}| It is the same manner as the FDD. If you are pulled to the top thrusting a hand in the expansion box is good in order to remove vertically. | | |{{:x68000:open_compact_15.jpg?300|}}| | |
| |{{:x68000:open_compact_18.jpg?200|}}| | |{{:x68000:open_compact_16.jpg?300|}}| | |
| |{{:x68000:open_compact_19.jpg?200|}}| | |{{:x68000:open_compact_17.jpg?300|}}| Carefully remove the I/O slot riser by lifting it vertically. | |
| |{{:x68000:open_compact_20.jpg?200|}}| | |{{:x68000:open_compact_18.jpg?300|}}| Unhook the two plastic tabs and turn the PSU diagonally. | |
| |{{:x68000:open_compact_21.jpg?200|}}| | |{{:x68000:open_compact_19.jpg?300|}}| Disconnect the power connector that is connected to the motherboard and cable which goes to the speaker. | |
| |{{:x68000:open_compact_22.jpg?200|}}| | |{{:x68000:open_compact_20.jpg?300|}}| Unhook the two white plastic tabs which are left and right, unplug the flat cable and carefully remove the rear connector board diagonally. | |
| |{{:x68000:open_compact_23.jpg?200|}}| | |{{:x68000:open_compact_21.jpg?300|}}| | |
| |{{:x68000:open_compact_24.jpg?200|}}| | |{{:x68000:open_compact_22.jpg?300|}}| Carefully and slowly remove the base. It should be possible to remove it without bending the shielding and without using force. | |
| |{{:x68000:open_compact_25.jpg?200|}}| | |{{:x68000:open_compact_23.jpg?300|}}| Unplug the speaker cable. | |
| |{{:x68000:open_compact_26.jpg?200|}}| | |{{:x68000:open_compact_24.jpg?300|}}| Unplug the circled connector. | |
| |{{:x68000:open_compact_27.jpg?200|}}| | |{{:x68000:open_compact_25.jpg?300|}}| | |
| |{{:x68000:open_compact_28.jpg?200|}}| | |{{:x68000:open_compact_26.jpg?300|}}| Remove the lower connector board (mouse keyboard joystick). Unhook the white plastic tabs and unplug the flat cable. | |
| | |{{:x68000:open_compact_27.jpg?300|}}| Unhook the white plastic tabs and remove the motherboard. | |
| | |{{:x68000:open_compact_28.jpg?300|}}| | |
