| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| x68000:how_to_open_x68000_compact [2014/08/13 02:42] – eidis | x68000:how_to_open_x68000_compact [2019/08/27 20:45] (current) – external edit 127.0.0.1 |
|---|
| All info taken from http://x68k-retro.cocolog-nifty.com/blog/2008/04/x68000_compact__11fb.html | All info taken from http://x68k-retro.cocolog-nifty.com/blog/2008/04/x68000_compact__11fb.html |
| |
| |{{:x68000:open_compact_01.jpg?300|}}| Remove the screws on the bottom → only one. | | |{{:x68000:open_compact_01.jpg?300|}}| Unscrew the screw at the bottom. | |
| |{{:x68000:open_compact_02.jpg?300|}}| Remove Slide the bottom part | | |{{:x68000:open_compact_02.jpg?300|}}| Slide and remove the bottom part. | |
| |{{:x68000:open_compact_03.jpg?300|}}| Remove the cover of the expansion board → use the driver again Since there is a nail → Remove the panel on the left when viewed from the front, remove the base there. | | |{{:x68000:open_compact_03.jpg?300|}}| Remove the expansion board cover. Open the left panel, when viewed from the front. | |
| |{{:x68000:open_compact_04.jpg?300|}}| I remove the panel on the right side. This ※ Remove the shield on the left to remove it towards the top and from the bottom → Remove the panel in the back, is OK at any timing. | | |{{:x68000:open_compact_04.jpg?300|}}| Remove the panel on the right side. Remove the shield on the left. Remove the back panel. It removes from bottom to top. | |
| |{{:x68000:open_compact_05.jpg?300|}}| To detach twist as photo while pulling it back → | | |{{:x68000:open_compact_05.jpg?300|}}| | |
| |{{:x68000:open_compact_06.jpg?300|}}| Remove the panel at the top | | |{{:x68000:open_compact_06.jpg?300|}}| Remove the panel at the top. Twist it as shown in the photo and pull it back. | |
| |{{:x68000:open_compact_07.jpg?300|}}| There are claws of two places in upper and disconnect it on the side of the nail down, is the front panel of the northeast. Please check with a photograph detent position, respectively. | | |{{:x68000:open_compact_07.jpg?300|}}| This is the front panel. Unhook the plastic tabs at the bottom and in two places at the top. Use photos for reference. | |
| |{{:x68000:open_compact_08.jpg?300|}}| | | |{{:x68000:open_compact_08.jpg?300|}}| | |
| |{{:x68000:open_compact_09.jpg?300|}}| | | |{{:x68000:open_compact_09.jpg?300|}}| | |
| |{{:x68000:open_compact_10.jpg?300|}}| It is easy to remove nails left when viewed from the front. Remove the nails so as to lift with a flathead screwdriver → this is located at the position of the button at the top right side of the nail, I pull on the front. Please put a force, making sure that the claws are out to ensure. | | |{{:x68000:open_compact_10.jpg?300|}}| It is easy to unhook plastic tabs from the front. Unhook the plastic tabs by lifting them with a flathead screwdriver and lift the bezel. | |
| |{{:x68000:open_compact_11.jpg?300|}}| | |{{:x68000:open_compact_11.jpg?300|}}| |
| |{{:x68000:open_compact_12.jpg?300|}}| It is a cinch the rest. I remove the white ring of 1. vinyl tape 2. plastic that holds the power cable. | | |{{:x68000:open_compact_12.jpg?300|}}| The rest is easy. Unhook the white plastic ring and vinyl tape that holds the power cable. | |
| |{{:x68000:open_compact_13.jpg?300|}}| 3.5 inches FDD | | |{{:x68000:open_compact_13.jpg?300|}}| Unplug the flat cables from 3.5" FDD drives. | |
| |{{:x68000:open_compact_14.jpg?300|}}| I Remove the flat cable. I remove the cable side of the FDD. Pull over to after removing each receive an equal part of the nail sure that stopped four places in the claws of the plastic. | | |{{:x68000:open_compact_14.jpg?300|}}| Unhook the four plastic tabs and remove the FDD drives. | |
| |{{:x68000:open_compact_15.jpg?300|}}| If you do not remove the expansion box ※ carefully, bracket for board expansion ※ breaks the board unchecked? It does not come off that it is not removed from the body all the bracket. Pull over to after removing each receive an equal part of the nail sure that stopped four places in the claws of the plastic. | | |{{:x68000:open_compact_15.jpg?300|}}| | |
| |{{:x68000:open_compact_16.jpg?300|}}| | | |{{:x68000:open_compact_16.jpg?300|}}| | |
| |{{:x68000:open_compact_17.jpg?300|}}| It is the same manner as the FDD. If you are pulled to the top thrusting a hand in the expansion box is good in order to remove vertically. | | |{{:x68000:open_compact_17.jpg?300|}}| Carefully remove the I/O slot riser by lifting it vertically. | |
| |{{:x68000:open_compact_18.jpg?300|}}| After you remove each receive an equal part of the nail sure that halted for two places in the claws of power plastic, I'll pull diagonally on. | | |{{:x68000:open_compact_18.jpg?300|}}| Unhook the two plastic tabs and turn the PSU diagonally. | |
| |{{:x68000:open_compact_19.jpg?300|}}| When the space can, I will disconnect the power connector that is connected to the main base. small nails It comes with the connector, I will be out even if not pulled with all his strength. | | |{{:x68000:open_compact_19.jpg?300|}}| Disconnect the power connector that is connected to the motherboard and cable which goes to the speaker. | |
| |{{:x68000:open_compact_20.jpg?300|}}| cable of the speaker, so we hit the power supply fan section, Do not hook. Rear connector board (SCSI) So there is a (white) plastic nails in two places left and right and remove the flat cable, I will remove the nails | | |{{:x68000:open_compact_20.jpg?300|}}| Unhook the two white plastic tabs which are left and right, unplug the flat cable and carefully remove the rear connector board diagonally. | |
| |{{:x68000:open_compact_21.jpg?300|}}| Lift Carefully the connector side, so as to slide diagonally on. Connector and rear panel, but you caught, Please support slowly improvise. It is a shield that surrounds the shield plate whole. | |{{:x68000:open_compact_21.jpg?300|}}| | |
| There are several places nails. First of all, please remove the claws of the position of the photo. | | |{{:x68000:open_compact_22.jpg?300|}}| Carefully and slowly remove the base. It should be possible to remove it without bending the shielding and without using force. | |
| |{{:x68000:open_compact_22.jpg?300|}}| I will continue to slowly remove the base there after. It has become to be able to remove without bending the shield without use force, (sorry will be more ad lib here) Let's remove it calmly | | |{{:x68000:open_compact_23.jpg?300|}}| Unplug the speaker cable. | |
| |{{:x68000:open_compact_23.jpg?300|}}| Speaker shield Once out, speaker terminal is visible. | | |{{:x68000:open_compact_24.jpg?300|}}| Unplug the circled connector. | |
| |{{:x68000:open_compact_24.jpg?300|}}| I will remove slowly or something pliers. You should remember where the enclosure cable speaker whether through before removing. | | |{{:x68000:open_compact_25.jpg?300|}}| | |
| |{{:x68000:open_compact_25.jpg?300|}}| And lower connector board (mouse keyboard joystick) (Easiest) to remove the nails of plastic (white) two positions I Remove the flat cable. | | |{{:x68000:open_compact_26.jpg?300|}}| Remove the lower connector board (mouse keyboard joystick). Unhook the white plastic tabs and unplug the flat cable. | |
| |{{:x68000:open_compact_26.jpg?300|}}| | | |{{:x68000:open_compact_27.jpg?300|}}| Unhook the white plastic tabs and remove the motherboard. | |
| |{{:x68000:open_compact_27.jpg?300|}}| You will work to remove the body of the main board from here Make sure the position (plastic? Vinyl? Still in place) of the claws turned over to the back side of the substrate. I will continue to remove the order from the white part of the nail. | | |{{:x68000:open_compact_28.jpg?300|}}| | |
| |{{:x68000:open_compact_28.jpg?300|}}| I will continue to remove the claws of the black part later. You remember well the wiring of the flat cable that is connected to the bottom connector board 1. Once ready to board floats. → I want to be easy to leave the flat cable 2.FDD, rear connector board (SCSI), which goes through the position has changed. If pulling as it is, you can remove the board. | | |
