x68000:internet_on_x68000_using_ethernet_or_null_modem_cable
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
x68000:internet_on_x68000_using_ethernet_or_null_modem_cable [2013/05/26 11:02] – fixed up the headings neko68k | x68000:internet_on_x68000_using_ethernet_or_null_modem_cable [2019/08/27 20:45] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 3: | Line 3: | ||
This article is a kind contribution by our forum member **Neko68k**. Thank you for shedding light on this rather grey area ! | This article is a kind contribution by our forum member **Neko68k**. Thank you for shedding light on this rather grey area ! | ||
- | This article will cover configuring your X68000 for internet access using either a null-modem cable or an ethernet card. Neptune-X | + | This article will cover configuring your X68000 for internet access using either a null-modem cable or an ethernet card. Neptune-X, Nereid, and RaSCSI |
==== Downloads ==== | ==== Downloads ==== | ||
Line 13: | Line 13: | ||
=== For Ethernet === | === For Ethernet === | ||
|[[http:// | |[[http:// | ||
+ | |||
+ | === For Emulated Ethernet === | ||
+ | |[[http:// | ||
=== For Serial === | === For Serial === | ||
Line 47: | Line 50: | ||
==== Serial Instructions ==== | ==== Serial Instructions ==== | ||
- | *unlzh PPPXR5.lzh | + | *Unlzh PPPXR5.lzh |
- | *put PPP.SYS in \SYS | + | *Put the contents of this LZH into the same directory. |
- | *put PPP.X KILL.X and PPPX.BAT in \BIN | + | *Be sure to modify the first line of PPPX.BAT to point to that directory. |
- | + | *Add ' | |
- | If you install PPP.X anywhere else, be sure to modify the first line of PPPX.BAT to point to that directory. | + | |
- | + | ||
- | I found it helpful to add the following line to the end of PPPX.BAT: | + | |
- | + | ||
- | < | + | |
- | + | ||
- | You have to do this anyway so might as well just make it happen. This is to point at your dns server, I used the IP address of my router. | + | |
- | + | ||
- | While you're at it, change: | + | |
- | + | ||
- | < | + | |
- | to | + | |
- | < | + | |
- | + | ||
- | This utilizes the faster | + | |
*unlzh TMSIO031.LZH and put TMSIO.X in \BIN | *unlzh TMSIO031.LZH and put TMSIO.X in \BIN | ||
| | ||
Line 81: | Line 69: | ||
[[http:// | [[http:// | ||
- | *On your x68k run PPPX.BAT. On the emulator this throws an error, it can be safely ignored. | + | I followed |
- | *Once at the ppp> prompt type 'term' | + | |
- | + | ||
- | *On your Linux machine(I am using Ubuntu 10.10 Maverick Meerkat) open a terminal. | + | |
- | *At the prompt type the following where: | + | |
- | *192.168.0.10 | + | |
- | */dev/ttyS0 is your serial port(ttyS0:COM1 ttyS1:COM2 etc) | + | |
- | + | ||
- | < | + | |
- | + | ||
- | If everything worked you should see something like this: | + | |
- | |{{: | + | |
+ | *On your x68k run PPPX.BAT. | ||
+ | *Once at the ppp> prompt type 'set debug 0' and push enter | ||
+ | *Then type ' | ||
+ | *Press enter again to get a login prompt | ||
+ | *Login as usual | ||
+ | *If everything is correct PPP will automatically negotiate the connection and drop you back to the command line. | ||
+ | *You should see a line that reads OsLinkup followed by 'PPP process kept.' | ||
==== Ethernet Instructions ==== | ==== Ethernet Instructions ==== | ||
Thanks to GIMONS for pointing me in the right direction. | Thanks to GIMONS for pointing me in the right direction. | ||
- | XM6G Specifics: | + | === General === |
- | *Use OpenVPN TAP driver. | + | |
- | | + | Add your ethernet |
- | | + | |
- | *In XM6G put your TAP interface name in the Nererid tab. | + | |
- | | + | |
I recommend creating a BAT file with the following commands: | I recommend creating a BAT file with the following commands: | ||
< | < | ||
xip -t -1 | xip -t -1 | ||
- | ifconfig | + | ifconfig |
- | ifconfig en0 192.168.0.11 | + | ifconfig en0 x68k netmask 255.255.255.0 up |
- | inetdconf +dns 192.168.0.1 +domain x68k +router 192.168.0.1 | + | inetdconf +dns 8.8.8.8 +domain x68k +router 192.168.0.1 |
</ | </ | ||
- | Run your BAT file. | + | In the above snippet ' |
+ | |||
+ | Run your BAT file and test with ' | ||
+ | |||
+ | === XM6G Specifics === | ||
+ | *Use OpenVPN TAP driver. | ||
+ | | ||
+ | *You _must_ set a static IP to the TAP device before bridging. This IP should be in your local subnet and will be the IP address for the x68k. It should be specified in /etc/hosts as described above. (ex. 10.0.0.x, 162.168.0.x). The default router should be _your_ router (ex. 10.0.0.1, 192.168.0.1). | ||
+ | | ||
+ | *In XM6G put your TAP interface name in the Nereid tab. | ||
+ | | ||
+ | *Now follow the General instructions above if you haven' | ||
+ | |||
x68000/internet_on_x68000_using_ethernet_or_null_modem_cable.1369530123.txt.gz · Last modified: 2019/08/27 20:44 (external edit)